Nissan Note E12. Instruction — part 668
TM-230
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
CONTROL CABLE
CONTROL CABLE
Exploded View
INFOID:0000000009020020
Removal and Installation
INFOID:0000000009020021
CAUTION:
Always apply the parking brake before performing removal and installation.
REMOVAL
1. Remove the battery negative terminal. Refer to
2. Remove the TCM and bracket. Refer to
TM-235, "Removal and Installation"
.
3. Remove the IPDM E/R. Refer to
PCS-30, "Removal and Installation"
.
4. Remove the battery tray and bracket.
5. Remove instrument lower panel LH. Refer to
IP-24, "Removal and Installation"
.
6. Remove the center console. Refer to
IP-18, "Removal and Installation"
.
7. Remove the control cable from the shift selector assembly.
8. Disengage the pawls (B) of the grommet (A), and pull downward
to remove.
9. Remove the control cable nut from the instruction lever.
1.
Bracket B
2.
Lock plate
3.
Transaxle assembly
4.
Bracket A
5.
Control cable
6.
CVT shift selector assembly
A: Instruction lever
B: Grommet
JSDIA1921GB
JSDIA1809ZZ
CONTROL CABLE
TM-231
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
10. Remove the lock plate (1).
11. Lift up the heat plate.
12. Remove the control cable (1) from the bracket (2).
13. Remove the control cable from the vehicle.
14. Remove bracket.
INSTALLATION
Installation is in the reverse order of removal.
• From below the vehicle, press the grommet (A) into place until the
pawls (B) make a click sound.
CAUTION:
Check that pulling down on the grommet does not disconnect
it.
• Pay attention to the following when connecting the control cable to the shift selector.
1. When connecting the control cable (1) to the shift selector
assembly (2), face the grooved surface of the rib (A) up and
insert the control cable until it stops.
JSDIA1812ZZ
Front
JPDIA0107ZZ
JSDIA1809ZZ
JSDIA1624ZZ
TM-232
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
CONTROL CABLE
2. Install the socket (A) onto the shift selector assembly.
CAUTION:
• Insert the socket into the shift selector assembly, then
push it firmly in place.
• Check that pulling on the socket does not disconnect it.
Inspection and Adjustment
INFOID:0000000009020022
INSPECTION AFTER INSTALLATION
Check CVT position. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust CVT position. Refer to
JSDIA1810ZZ
KEY INTERLOCK CABLE
TM-233
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
KEY INTERLOCK CABLE
Exploded View
INFOID:0000000009020023
Removal and Installation
INFOID:0000000009020024
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1. Move the shift selector to the “N” position.
2. Remove the shift selector handle. Refer to
TM-228, "Disassembly and Assembly"
.
3. Remove the instrumental lower panel LH. Refer to
IP-24, "Removal and Installation"
.
4. Remove steering column covers. Refer to
IP-17, "Removal and Installation"
.
5. Remove the center console. Refer to
IP-18, "Removal and Installation"
.
6. Move the shift selector to the “P” position.
7. Press the pawls (B) of the key interlock cable slider (A) while
sliding it in the direction of the casing cap (C), and separate the
adjusting holder (D) and slider.
8. Remove the key interlock cable from the shift selector assembly.
1.
Shift selector assembly
2.
Key interlock cable
A: Key cylinder
B: Lock plate
C: Clip
ALDIA0262ZZ
(E)
:Key interlock rod
JSDIA1797ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст