Nissan Note E12. Instruction — part 196
FUEL PRESSURE CHECK
EC-123
< BASIC INSPECTION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4. Connect fuel hose for fuel pressure check to fuel tube (engine
side) with clamp as shown in the figure.
CAUTION:
• Wipe off oil or dirt from hose insertion part using cloth
moistened with gasoline.
• Apply proper amount of gasoline between top of the fuel
tube and No.1 spool .
• Insert fuel hose for fuel pressure check until it touches
the No.1 spool on fuel tube.
• Use NISSAN genuine hose clamp (part number: 16439 N4710 or 16439 40U00).
• When reconnecting fuel line, always use new clamps.
• Use a torque driver to tighten clamps.
• Install hose clamp to the position within 1 - 2 mm (0.04 - 0.08 in).
• Make sure that clamp screw does not contact adjacent parts.
5. Connect fuel tube adapter to quick connector .
6. After connecting fuel hose for fuel pressure check, pull the hose
with a force of approximately 98 N (10 kg, 22 lb) to confirm fuel
tube does not come off.
7. Turn ignition switch ON and check for fuel leakage.
8. Start engine and check for fuel leakage.
9. Read the indication of fuel pressure gauge.
CAUTION:
• Do not perform fuel pressure check with system operat-
ing. Fuel pressure gauge may indicate false readings.
• During fuel pressure check, confirm for fuel leakage from fuel connection every 3 minutes.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK FUEL HOSE AND FUEL TUBE
If result is unsatisfactory, check fuel hoses and fuel tubes for clogging.
Is the inspection result normal?
YES
>> Replace “fuel filter and fuel pump assembly”. Refer to
.
NO
>> Repair or replace.
: No.2 spool
Tightening torque : 1 - 1.5 N·m (0.1 - 0.15 kg-m, 9 - 13 in-lb)
A : Fuel pressure gauge
At idling
: Approximately 350 kPa (3.5 bar, 3.57 kg/cm
2
, 51 psi)
PBIB2983E
ALBIA1073ZZ
EC-124
< BASIC INSPECTION >
[HR16DE]
HOW TO SET SRT CODE
HOW TO SET SRT CODE
Description
INFOID:0000000009022492
OUTLINE
In order to set all SRTs, the self-diagnoses as in the “SRT ITEM” table must have been performed at least
once. Each diagnosis may require actual driving for a long period of time under various conditions.
SRT ITEM
The table below shows required self-diagnostic items to set the SRT to “CMPLT”.
*: Though displayed on the CONSULT screen, “HO2S HTR” is not SRT item.
SRT SERVICE PROCEDURE
If a vehicle has failed the state emissions inspection due to one or more SRT items indicating “INCMP”, review
the flowchart diagnostic sequence, referring to the following flowchart.
SRT item
*
(CONSULT indication)
Required self-diagnostic items to set the SRT to “CMPLT”
Corresponding DTC No.
CATALYST
Three way catalyst function
P0420
HO2S
Air fuel ratio (A/F) sensor 1
P0130, P0133
Heated oxygen sensor 2
P0137
Heated oxygen sensor 2
P0138
Heated oxygen sensor 2
P0139
HOW TO SET SRT CODE
EC-125
< BASIC INSPECTION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
SRT Set Driving Pattern
INFOID:0000000009022493
CAUTION:
JSBIA0399GB
EC-126
< BASIC INSPECTION >
[HR16DE]
HOW TO SET SRT CODE
Always drive the vehicle in safe manner according to traffic conditions and obey all traffic laws.
NOTE:
*1: Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then release the accelerator pedal
and keep it released for more than 10 seconds. Depress the accelerator pedal until vehicle speed is 90 km/h
(56 MPH) again.
*2: Checking the vehicle speed with GST is advised.
• The time required for each diagnosis varies with road surface conditions, weather, altitude, individual driving
habits, etc.
JSBIA1318GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст