Nissan Note E12. Instruction — part 648
TM-150
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0706 TRANSMISSION RANGE SENSOR A
7.
CHECK CIRCUIT BETWEEN IPDM E/R AND TRANSMISSION RANGE SWITCH
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and transmission range switch.
Is the check result normal?
YES
>> GO TO 8.
NO
>> Repair or replace malfunctioning parts.
8.
DETECT MALFUNCTIONING ITEMS
Check the following items:
• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to
gram — Ignition Power Supply —"
• Short circuit in harness between IPDM E/R harness connector terminal 21 and transmission range switch
harness connector terminal 4.
• 10A fuse (No. 49, IPDM E/R). Refer to
PG-39, "IPDM E/R Terminal Arrangement"
.
• IPDM E/R
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection (Transmission Range Switch)
INFOID:0000000009019928
1.
CHECK TRANSMISSION RANGE SWITCH
Check continuity between transmission range switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to
250, "Removal and Installation"
.
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
E45
21
F52
4
Existed
Transmission range switch
Condition
Continuity
Terminal
7 – 10
Instruction lever: “P” and “N” positions
Existed
Other than the above
Not existed
4 – 5
Instruction lever: “P” position
Existed
Other than the above
Not existed
4 – 8
Instruction lever: “R” position
Existed
Other than the above
Not existed
4 – 9
Instruction lever: “N position
Existed
Other than the above
Not existed
4 – 2
Instruction lever: “D” position
Existed
Other than the above
Not existed
4 – 6
Instruction lever: “L” position
Existed
Other than the above
Not existed
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
TM-151
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
DTC Logic
INFOID:0000000009019929
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following conditions for a total of 10 minutes or more.
4. Stop the vehicle.
5. Check the first trip DTC.
Is “P0711” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009019930
1.
CHECK CVT FLUID TEMPERATURE SENSOR
1. Turn ignition switch OFF.
2. Disconnect CVT unit connector.
3. Check CVT fluid temperature sensor. Refer to
TM-152, "Component Inspection (CVT Fluid Temperature
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0711
Transmission Fluid Tempera-
ture Sensor A Circuit Range/
Performance
Under the following diagnosis conditions, CVT
fluid temperature recognized by TCM does not
change for 10 minutes or more in a tempera-
ture range.
• Diagnosis condition
- Selector lever: “D” position
- Vehicle speed: 10 km/h (7 MPH) or more
- Engine speed: 450 rpm or more
- Accelerator pedal position: 1.0/8 or more
- TCM power supply voltage: More than 11 V
- CVT fluid temperature: Less than 10
°C
NOTE:
Every time the CVT fluid temperature increas-
es, reset the detection time and start the diag-
nosis again.
CVT fluid temperature sensor
Selector lever
: “D” position
Accelerator pedal position
: 1.0/8 or more
Vehicle speed
: 20 km/h (12 MPH) or more
TM-152
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
Component Inspection (CVT Fluid Temperature Sensor)
INFOID:0000000009019931
1.
CHECK CVT FLUID TEMPERATURE SENSOR
Check resistance between CVT unit connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of CVT fluid temperature sensor. Replace transaxle assembly. Refer to
TM-250, "Removal and Installation"
CVT unit
Condition
Resistance
(Approx.)
Terminal
12 – 18
CVT fluid temperature: 20
°C (68°C)
6.5 k
Ω
CVT fluid temperature: 50
°C (122°C)
2.2 k
Ω
CVT fluid temperature: 80
°C (176°C)
0.87 k
Ω
P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A
TM-153
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A
DTC Logic
INFOID:0000000009019932
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and wait for 10 seconds or more.
2. Check the first trip DTC.
Is “P0712” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009019933
1.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning part.
2.
CHECK CVT FLUID TEMPERATURE SENSOR
Check CVT fluid temperature sensor. Refer to
TM-153, "Component Inspection (CVT Fluid Temperature Sen-
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection (CVT Fluid Temperature Sensor)
INFOID:0000000009019934
1.
CHECK CVT FLUID TEMPERATURE SENSOR
Check resistance between CVT unit connector terminals.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0712
Transmission Fluid Tempera-
ture Sensor A Circuit Low
The CVT fluid temperature identified by the
TCM is 180
°C (356°F) or more continuously
for 5 seconds or more under the following di-
agnosis conditions:
• Diagnosis conditions
- Ignition switch: ON
- TCM power supply voltage: More than 11 V
• Harness or connector
(CVT fluid temperature sensor circuit is
shorted to ground)
• CVT fluid temperature sensor
TCM
—
Continuity
Connector
Terminal
F44
12
Ground
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст