Nissan Note E12. Instruction — part 454
MWI-2
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . .
B2267 ENGINE SPEED . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
B2268 WATER TEMP . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
POWER SUPPLY AND GROUND CIRCUIT . .
COMBINATION METER . . . . . . . . . . ...
COMBINATION METER : Diagnosis Procedure ....
BODY CONTROL SYSTEM . . . . . . . . . ..
BODY CONTROL SYSTEM : Diagnosis Proce-
dure . . . . . . . . . . . . . . . . . ....
FUEL LEVEL SENSOR SIGNAL CIRCUIT . ...
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . .
THE FUEL GAUGE INDICATOR DOES NOT
OPERATE . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE OIL PRESSURE WARNING LAMP
DOES NOT TURN ON . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE OIL PRESSURE WARNING LAMP
DOES NOT TURN OFF . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
THE DOOR OPEN WARNING CONTINUES
DISPLAYING, OR DOES NOT DISPLAY . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
UNIT REMOVAL AND INSTALLATION .
COMBINATION METER . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY ...
COMBINATION METER . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
MWI
PRECAUTIONS
MWI-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009473005
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
MWI-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000009482448
Tool name
Description
Power Tool
Loosening nuts, screws and bolts
PIIB1407E
MWI
COMPONENT PARTS
MWI-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
METER SYSTEM
METER SYSTEM : Component Parts Location
INFOID:0000000009561107
A.
Combination meter
B.
View with inspection hole cover removed.
No.
Component
Function
1.
Parking brake switch
Transmits the parking brake switch signal to the combination meter.
2.
ABS actuator and electric unit (control unit)
Transmits the vehicle speed signal to the combination meter via CAN communica-
tion.
Refer to
BRC-6, "Component Parts Location"
for detailed installation location.
3.
Engine oil pressure sensor
Transmits the engine oil pressure sensor signal to the ECM.
Refer to
for detailed installation location.
4.
TCM
Transmits the shift position signal to the combination meter via CAN communica-
tion.
Refer to
TM-59, "CVT CONTROL SYSTEM : Component Parts Location"
for de-
tailed installation location.
5.
ECM
Transmits the following signals to the combination meter via CAN communication.
• Engine speed signal
• Engine coolant temperature signal
• Fuel consumption monitor signal
• Engine oil pressure sensor signal
Refer to
EC-11, "ENGINE CONTROL SYSTEM : Component Parts Location"
for
detailed installation location.
AWNIA3079ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст