Nissan Note E12. Instruction — part 593
STEERING COLUMN
ST-11
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check tilt mechanism operating range (T) as shown.
Tilt operating range (T)
: Refer to
JPGIA0043ZZ
ST-12
< REMOVAL AND INSTALLATION >
STEERING SHAFT
STEERING SHAFT
Exploded View
INFOID:0000000009385590
Removal and Installation
INFOID:0000000009385591
REMOVAL
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column and steering gear. Be
sure to secure steering wheel using string to avoid turning.
1. Set the front wheels and tires in the straight-ahead position.
2. Set the steering column tilt to the middle position.
CAUTION:
Securely lock the tilt lever.
3. Remove instrument lower panel LH. Refer to
IP-24, "Removal and Installation"
.
4. Loosen lower joint upper bolt.
5. Remove lower joint lower bolt and separate lower joint from the steering gear lower shaft.
CAUTION:
• Place a matching mark on both lower joint and steering gear lower shaft before removing lower
joint.
• When removing lower joint, do not insert any tool into the yoke groove to pull out the lower joint.
Replace the lower joint if damaged.
6. Remove lower joint from steering intermediate shaft.
7. Remove the steering intermediate shaft bolt, from steering column, and remove steering intermediate
shaft from steering column.
CAUTION:
• Place a matching mark on both steering intermediate shaft and steering column before removing
steering intermediate shaft.
• When removing the steering intermediate shaft, do not insert any tool into the yoke groove to
pull out the steering intermediate shaft or damage could occur. Replace the steering intermedi-
ate shaft if damaged.
INSTALLATION
CAUTION:
During installation, finger-tighten all of the bracket and joint retaining bolts; then tighten them to spec-
ification. Do not apply undue stress to the steering column.
Installation is in the reverse order of removal.
1.
Lower joint
2.
Steering intermediate shaft
3.
Steering column
JPGIA0112GB
STEERING SHAFT
ST-13
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Before installation, check that steering column tilt is in the middle position.
• For intermediate shaft bolt, and lower joint bolt direction, refer to
• To install align the steering gear guide protrusion (A) with the
groove of lower joint (1), make sure the bolt is securely seated in
groove (B) of steering gear before final tightening.
CAUTION:
If a guide protrusion is not included, align with the matching
mark placed at the removal step.
• When tightening lower joint bolt to the steering gear lower shaft,
temporarily tighten it and make sure there is no sticking or galling
before final tightening.
• When connecting intermediate shaft upper side (1) and column
shaft, make sure the bolt is securely seated in groove (A) of col-
umn shaft before final tightening.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000009385592
INSPECTION AFTER REMOVAL
• Check each part of steering intermediate shaft, lower joint, and steering column for damage or other mal-
functions. Replace if there are any abnormal conditions.
INSPECTION AFTER INSTALLATION
• Rotate steering wheel to make sure it is centered and there is no binding, noise or excessive steering effort.
• Make sure that the number of turns are the same from the straight-ahead position to the left and right locks.
• Check each part of steering intermediate shaft, lower joint, and steering column for damage or other mal-
functions. Replace if there are any abnormal conditions.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
JPGIA0041ZZ
SGIA1295E
ST-14
< REMOVAL AND INSTALLATION >
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000009385593
Removal and Installation
INFOID:0000000009385594
CAUTION:
• Spiral cable may be cut if steering wheel turns while separating steering column and steering gear;
Always secure the steering wheel using string to avoid turning.
• Place a matching mark on both lower joint and steering gear before removing lower joint.
• When removing lower joint, do not place any tool into the yoke groove to pull out the lower joint.
Replace the lower joint if damaged.
REMOVAL
1. Set the front wheels and tires in the straight-ahead position.
2. Set the steering column tilt to the middle position.
CAUTION:
Securely lock the tilt lever.
3. Remove front suspension member. Refer to
FSU-14, "Removal and Installation"
4. Remove the steering gear bolts and nuts and separate the steering gear from the front suspension mem-
ber.
5. Separate cowl seal from steering gear if necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• During installation, finger-tighten all of the bracket and joint retaining bolts; then tighten them to
specification. Do not apply undue stress to the steering column.
• The guide protrusion is not required to be reinstalled.
• Before installation, check that the steering column tilt is in the middle position.
• Clean mating surface on the body side of cowl seal when installing steering gear assembly.
• Inspect steering gear after installation. Refer to
Inspection
INFOID:0000000009385595
INSPECTION AFTER REMOVAL
• Check each part of steering gear for damage or other malfunctions. Replace if there are any abnormal con-
1.
Guide
2.
Cowl seal
3.
Steering gear
4.
Front suspension member
Front
AWGIA0236ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст