Nissan Note E12. Instruction — part 400
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing rear kicking plate, check that clips and pawls are securely placed into body panel
holes.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000009016044
REMOVAL
1. Remove front kicking plate. Refer to
INT-20, "KICKING PLATE : Removal and Installation"
.
2. Lift up rear end of dash side finisher to release pawls.
: Pawl
3. Pull back dash side finisher to release dash side finisher from
stud and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the pawls for deformation and damage during installation.
• When installing, check that finisher is aligned with stud bolt located on floor panel.
• When installing dash side finisher, check that pawls are securely placed into body panel holes.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000009016045
FRONT BODY SIDE WELT
Removal
1. Remove the dash side finisher. Refer to
INT-22, "DASH SIDE FINISHER : Removal and Installation"
.
2. Remove front body side welt.
Installation
Installation is in the reverse order of removal.
REAR BODY SIDE WELT
Removal
1. Remove rear kicking plate. Refer to
INT-20, "KICKING PLATE : Removal and Installation"
2. Remove rear body side welt.
AWJIA1092ZZ
AWJIA1093ZZ
BODY SIDE TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
CENTER PILLAR LOWER FINISHER : Removal and Installation
INFOID:0000000009016046
REMOVAL
1. Remove front kicking plate and rear kicking plate. Refer to
INT-20, "KICKING PLATE : Removal and
.
2. Remove center pillar lower finisher as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the pawls and clips for deformation and damage during installation. Replace compo-
nent if necessary.
CENTER PILLAR UPPER FINISHER
CENTER PILLAR UPPER FINISHER : Removal and Installation
INFOID:0000000009016047
REMOVAL
CAUTION:
• Be careful not to apply excessive force when removing center pillar upper finisher. Otherwise, clip
may be damaged and fragments may drop in body panels.
1. Slide front seat to the full forward position.
2. Release pawls, using a suitable tool and remove the seat belt
height adjuster finisher (1).
: Pawl
3. Remove front D-ring anchor bolt.
CAUTION:
Before removing D-ring anchor bolt note the positions of washers and spacers for correct installa-
tion.
4. Remove front body side welt and rear body side welt. Refer to
INT-22, "BODY SIDE WELT : Removal and
.
5. Remove center pillar lower finisher. Refer to
INT-23, "CENTER PILLAR LOWER FINISHER : Removal
6. Release center pillar upper finisher upper clip using a suitable tool as shown.
CAUTION:
JMJIA6045ZZ
AWHIA0539ZZ
INT-24
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
When releasing molded in clip, follow the steps as shown to prevent finisher or clip damage.
7. Release center pillar upper finisher lower clip using a suitable
tool (A) and remove.
: Clip
CAUTION:
Do not reuse center pillar upper finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse center pillar upper finisher. Replace with new part for installation.
• When installing center pillar upper finisher, check that clips are securely placed in body panel holes.
PIIB2600J
AWJIA1094ZZ
FLOOR TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FLOOR TRIM
Exploded View
INFOID:0000000009541591
Removal and Installation
INFOID:0000000009016049
WARNING:
• Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals then wait at
least three minutes.
• Do not drop the seat belt retractor. Always handle it with care.
• Always point pretensioner cylinder away from body when handling.
REMOVAL
1. Remove front seats. Refer to
SE-14, "DRIVER SIDE : Removal and Installation"
(Driver side) and
"PASSENGER SIDE : Removal and Installation"
(Passenger side).
2. Remove rear seatback hinge. Refer to
SE-20, "SEATBACK HINGE : Removal and Installation"
3. Remove center console lower. Refer to
IP-20, "Removal and Installation"
4. Remove dash side finishers (LH/RH). Refer to
INT-22, "DASH SIDE FINISHER : Removal and Installa-
5. Remove center pillar lower finishers (LH/RH). Refer to
INT-23, "CENTER PILLAR LOWER FINISHER :
.
1.
Harness clip A
2.
Harness clip B
3.
Floor trim
4.
Carpet hook
5.
Front floor spacer (RH)
6.
Front floor spacer (LH)
7.
Rear floor spacer (LH)
8.
Rear floor spacer (RH)
Front
Clip
AWJIA1142ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст