Nissan Note E12. Instruction — part 367
HA-26
< REMOVAL AND INSTALLATION >
COMPRESSOR
Check the clearance (B) between pulley assembly (1) and clutch
disc (2) along the entire periphery with a feeler gauge (A).
If specified clearance is not obtained, replace adjusting spacer and
readjust.
Clearance
: Refer to
AWIIA1462ZZ
COOLER PIPE AND HOSE
HA-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
COOLER PIPE AND HOSE
Exploded View
INFOID:0000000009014875
LOW-PRESSURE FLEXIBLE HOSE
LOW-PRESSURE FLEXIBLE HOSE : Removal and Installation
INFOID:0000000009395304
REMOVAL
1. Discharge the refrigerant. Refer to
2. Disconnect vacuum hose from intake manifold. Refer to
3. Remove ground wire from engine to radiator core support upper.
4. Remove front grille. Refer to
EXT-21, "Removal and Installation"
5. Remove low-pressure flexible hose nut and bolt, then position lower dash insulator as necessary.
6. Remove bolt and low-pressure flexible hose from expansion valve.
CAUTION:
Cap or wrap the joint of the A/C hose and expansion valve with suitable material such as vinyl tape
to avoid the entry of air.
7. Remove bolt and low-pressure flexible hose from compressor.
CAUTION:
Cap or wrap the joint of the A/C hose and compressor with suitable material such as vinyl tape to
avoid the entry of air.
1.
Heating and cooling unit assembly
2.
O-ring
3.
High-pressure pipe
4.
Condenser
5.
High-pressure flexible hose
6.
Compressor
7.
Low-pressure flexible hose
AWIIA1685GB
HA-28
< REMOVAL AND INSTALLATION >
COOLER PIPE AND HOSE
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-rings.
• Apply compressor oil to new O-rings of low-pressure flexible hose for installation.
• After charging refrigerant, check for leaks. Refer to
HIGH-PRESSURE FLEXIBLE HOSE
HIGH-PRESSURE FLEXIBLE HOSE : Removal and Installation
INFOID:0000000009395305
REMOVAL
1. Discharge the refrigerant. Refer to
2. Remove front grille. Refer to
EXT-21, "Removal and Installation"
3. Remove bolt and high-pressure flexible hose from condenser.
CAUTION:
Cap or wrap the joint of the A/C hose and condenser with suitable material such as vinyl tape to
avoid the entry of air.
4. Remove bolt and high-pressure flexible hose from compressor.
CAUTION:
Cap or wrap the joint of the A/C hose and compressor with suitable material such as vinyl tape to
avoid the entry of air.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-rings.
• Apply compressor oil to new O-rings of the high-pressure flexible hose for installation.
• After charging refrigerant, check for leaks. Refer to
HIGH-PRESSURE PIPE
HIGH-PRESSURE PIPE : Removal and Installation
INFOID:0000000009395306
REMOVAL
1. Discharge the refrigerant. Refer to
2. Remove radiator core support upper. Refer to
DLK-122, "RADIATOR CORE SUPPORT UPPER :
.
3. Remove low-pressure flexible hose. Refer to
HA-27, "LOW-PRESSURE FLEXIBLE HOSE : Removal and
.
4. Remove high-pressure flexible hose. Refer to
HA-28, "HIGH-PRESSURE FLEXIBLE HOSE : Removal
5. Disconnect high-pressure pipe from expansion valve.
CAUTION:
Cap or wrap the joint of the A/C piping and expansion valve with suitable material such as vinyl
tape to avoid the entry of air.
6. Remove bolt and high-pressure pipe from condenser.
CAUTION:
Cap or wrap the joint of the A/C piping and condenser with suitable material such as vinyl tape to
avoid the entry of air.
7. Release clips and remove high-pressure pipe from vehicle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-rings.
• Apply compressor oil to new O-rings of the high-pressure pipe for installation.
• After charging refrigerant, check for leaks. Refer to
CONDENSER
HA-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
CONDENSER
Exploded View
INFOID:0000000009014876
CONDENSER
CONDENSER : Removal and Installation
INFOID:0000000009395310
REMOVAL
1. Discharge the refrigerant. Refer to
2. Remove front grille. Refer to
EXT-21, "Removal and Installation"
3. Remove air guides. Refer to
.
4. Remove radiator core support upper. Refer to
DLK-122, "RADIATOR CORE SUPPORT UPPER :
.
5. Remove bolt and high-pressure flexible hose from condenser.
CAUTION:
Cap or wrap the joint of the A/C hose and condenser with suitable material such as vinyl tape to
avoid the entry of air.
6. Remove bolt and high-pressure pipe from condenser.
CAUTION:
Cap or wrap the joint of the A/C piping and condenser with suitable material such as vinyl tape to
avoid the entry of air.
7. Disconnect the harness connector from the refrigerant pressure sensor and remove condenser.
CAUTION:
Be careful not to damage core surface of condenser.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-rings.
1.
Refrigerant pressure sensor
2.
Condenser with liquid tank
3.
O-ring
AWIIA1695ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст