Nissan Note E12. Instruction — part 685
WCS
THE LIGHT REMINDER WARNING DOES NOT SOUND
WCS-35
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description
INFOID:0000000009541248
Light reminder warning chime does not sound even though headlamps are illuminated.
Diagnosis Procedure
INFOID:0000000009541249
1.
CHECK COMBINATION METER INPUT SIGNAL
Select the Data Monitor for the METER/M&A and check the BUZZER monitor value.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-48, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT
Check the driver side door switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK DRIVER SIDE DOOR SWITCH
Check the driver side door switch. Refer to
DLK-85, "Component Inspection"
Is the inspection result normal?
YES
>> Replace the BCM. Refer to
BCS-67, "Removal and Installation"
NO
>> Replace driver side door switch. Refer to
DLK-158, "Removal and Installation"
Monitor Item
Condition
Status
BUZZER
Under the condition of buzzer input
ON
Except above
OFF
WT-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
WT
A
B
WT
N
O
P
CONTENTS
ROAD WHEELS & TIRES
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service Notice and Precautions for Road Wheel . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
WHEEL . . . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
WHEEL AND TIRE . . . . . . . . . . . .
Adjustment . . . . . . . . . . . . . . . ....
REMOVAL AND INSTALLATION . . . .
WHEEL AND TIRE . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ..
Wheel . . . . . . . . . . . . . . . . . ...
WT-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009445894
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Service Notice and Precautions for Road Wheel
INFOID:0000000009443478
• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.
• Use Genuine NISSAN parts for the road wheels, valve caps and wheel nuts.
• Always use them after adjusting the wheel balance. For the balance weights, use Genuine NISSAN alumi-
num wheel weights.
• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing
dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-
gent if a detergent is needed.
• After driving on roads scattered with anti-icing salts, wash off the wheels completely.
• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them
from being trapped between the contact surfaces of wheel.
• Do not apply oil to nut and bolt threads.
• When tightening the valve cap there is a risk of damaging the valve cap if a tool is used. Tighten by hand.
PREPARATION
WT-3
< PREPARATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000009443480
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст