Nissan Note E12. Instruction — part 559
SEC-88
< DTC/CIRCUIT DIAGNOSIS >
B2604 SHIFT POSITION
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK TRANSMISSION RANGE SWITCH
SEC-88, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Replace transmission range switch.
8.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
>> Inspection End.
9.
REPLACE BCM
1. Replace BCM. Refer to
BCS-67, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
Component Inspection
INFOID:0000000009567445
1.
CHECK TRANSMISSION RANGE SWITCH
1. Turn ignition switch OFF.
2. Disconnect transmission range switch connector.
3. Check continuity between transmission range switch terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace transmission range switch.
Transmission range switch
Condition
Continuity
Terminal
7
10
P or N position
Yes
Other than above
No
B2605 SHIFT POSITION
SEC-89
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2605 SHIFT POSITION
DTC Logic
INFOID:0000000009567446
DTC DETECTION LOGIC
NOTE:
• If DTC B2605 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2605 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Shift the selector lever to the P position.
2. Turn ignition switch ON and wait 1 second or more.
3. Shift the selector lever to the N position and wait 1 second or more.
4. Shift the selector lever to any position other than P and N, and wait 1 second or more.
5. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009567447
Regarding Wiring Diagram information, refer to
.
1.
CHECK IPDM E/R INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK IPDM E/R INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Disconnect transmission range switch connector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2605
SHIFT PN DIAG IPDM
When ignition switch is ON, P/N position
signal input from transmission range switch
and P/N position signal (CAN) input from
IPDM E/R do not match.
• Harness or connectors
(The CAN communication line is open or
shorted.)
• Harness or connectors
(Transmission range switch circuit is
open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
F42
40
Ground
Selector lever
P or N position
Battery voltage
Other than above
0
S E C - 9 0
< DTC/CIRCUIT DIAGNOSIS >
B2605 SHIFT POSITION
4. Check continuity between IPDM E/R harness connector and transmission range switch harness connec-
tor.
5. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
3.
CHECK BCM INPUT SIGNAL
1. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK BCM INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Disconnect transmission range switch connector.
4. Check continuity between BCM harness connector and transmission range switch harness connector.
5. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
REPLACE BCM
1. Replace BCM. Refer to
BCS-67, "Removal and Installation"
.
2. Perform initialization of BCM using CONSULT. Refer to the CONSULT Immobilizer mode and follow the
on-screen instructions.
3. Perform DTC CONFIRMATION PROCEDURE for B2605. Refer to
.
Is DTC B2605 detected again?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation"
NO
>> Inspection End.
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
F42
40
F52
10
Yes
IPDM E/R
Ground
Continuity
Connector
Terminal
F42
40
No
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M98
102
Ground
Selector lever
P or N position
Battery voltage
Other than above
0
BCM
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
M98
102
F52
10
Yes
BCM
Ground
Continuity
Connector
Terminal
M98
102
No
B2608 STARTER RELAY
SEC-91
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2608 STARTER RELAY
DTC Logic
INFOID:0000000009567448
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
• If DTC B2608 is displayed with other DTC (BCM), first perform the trouble diagnosis for other DTC detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under the following conditions to start engine.
-
Selector lever: In the P position
-
Brake pedal: Depressed
2. Wait 1 second after engine started.
3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009567449
Regarding Wiring Diagram information, refer to
.
1.
CHECK DTC OF IPDM E/R
Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK STARTER RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2608
STARTER RELAY
BCM outputs starter relay OFF signal but
BCM receives starter relay ON signal from
IPDM E/R (CAN).
• Harness or connectors
(The CAN communication line is open or
shorted.)
• Harness or connectors
(Starter relay circuit is open or shorted.)
• IPDM E/R
• Starter relay
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M98
97
Ground
CVT selector lever
N or P position
Battery voltage
Other than above
0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст