Nissan Xterra. Instruction — part 698
ASSEMBLY
TM-305
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5. Install instruction plate (with parking rod) to instruction shaft.
6. Install retaining pin into the instruction plate and instruction shaft.
a. Align pinhole of the manual plate to pinhole of the manual shaft
using suitable tool.
b. Tap the retaining pin into the instruction plate using suitable tool.
CAUTION:
• Drive retaining pin to 2
±0.5 mm (0.08±0.020 in) over the
instruction plate.
• Do not reuse retaining pin.
7. Install retaining pin into the transmission case and instruction shaft.
a. Align pinhole of the transmission case to pinhole of the instruction
shaft using suitable tool.
b. Tap the retaining pin into the transmission case using suitable
tool.
CAUTION:
• Drive retaining pin to 5
±1 mm (0.20±0.04 in) over the trans-
mission case.
• Do not reuse retaining pin.
8. Install O-rings to servo assembly.
CAUTION:
• Do not reuse O-rings.
• Apply petroleum jelly to O-rings.
9. Install return spring to servo assembly.
SCIA5715E
SCIA5297E
SCIA2427E
SCIA5719E
SCIA5717E
TM-306
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
ASSEMBLY
10. Install servo assembly in transmission case.
11. Install snap ring to transmission case using suitable tool.
12. Install D-rings in reverse brake piston.
CAUTION:
• Do not reuse D-rings.
• Apply ATF to D-rings.
13. Install reverse brake piston in transmission case.
14. Install needle bearing to drum support edge surface.
CAUTION:
Apply petroleum jelly to needle bearing.
SCIA5679E
SCIA2333E
SCIA6330E
SCIA2325E
SCIA2796E
ASSEMBLY
TM-307
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
15. Install seal rings to drum support.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
16. Install spring retainer and return spring in transmission case.
17. Install snap ring in transmission case while compressing return
spring using Tool.
CAUTION:
Securely assemble them using a flat-bladed screwdriver so
that snap ring tension is slightly weak.
18. Install reverse brake drive plates driven plates and dish plates in
transmission case.
CAUTION:
Take care with order of plates.
• VQ40DE models
- Snap ring (1)
- Retaining plate (2)
- Drive plate (3)
- Driven plate (4)
- Dish plate (5)
- Drive plate/Driven plate:6/6
SCIA3333E
SCIA2324E
Tool number
: KV31102400 (J-34285 and J-34285-87)
SCIA5877E
SCIA6949E
TM-308
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
ASSEMBLY
19. Assemble N-spring.
20. Install reverse brake retaining plate in transmission case.
21. Install snap ring in transmission case.
22. Measure clearance (A) between retaining plate and snap ring. If
not within specified clearance, select proper retaining plate.
23. Install needle bearing to transmission case.
CAUTION:
• Take care with the direction of needle bearing. Refer to
TM-265, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
SCIA5249E
SCIA2439E
Clearance “A”
: 0.7 - 1.1 mm (0.028 - 0.043 in)
Retaining plate
: Refer to
SCIA3129E
SCIA5031E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст