Nissan Xterra. Instruction — part 720
WT-42
< SYMPTOM DIAGNOSIS >
HAZARD WARNING LAMPS FLASH
HAZARD WARNING LAMPS FLASH
Hazard Warning Lamps Flash When Ignition Switch Is Turned On
INFOID:0000000009483098
DIAGNOSTIC PROCEDURE
1.
CHECK BCM GROUND CIRCUIT
Check BCM ground circuit. Refer to
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-50, "Removal and Installation"
NO
>> Repair BCM ground circuit.
ID REGISTRATION CANNOT BE COMPLETED
WT-43
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
ID REGISTRATION CANNOT BE COMPLETED
ID Registration Cannot Be Completed
INFOID:0000000009483099
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
DIAGNOSTIC PROCEDURE
1.
PERFORM ID REGISTRATION OF ALL TRANSMITTERS
Carry out ID registration of all transmitters. Refer to
.
Can ID registration of all transmitters be completed?
YES
>> Inspection End.
NO
>> GO TO
WT-44
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009483100
Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
—
—
,
,
,
,
"
,
,
Refe
r to
TI
RES in
th
is cha
rt.
Refe
r to
ROAD WHEE
L i
n t
his cha
rt.
Possible cause and SUSPECTED
PARTS
O
ut
-of-ro
un
d
Im
ba
la
nc
e
Incorrect t
ire
pressure
Uneven tire
wear
Def
orm
ati
on
or
da
ma
ge
No
n-u
n
iformi
ty
In
co
rrec
t t
ire
si
ze
FRONT A
N
D
REAR FINA
L DRIVE
FRONT A
X
LE
AND FRONT SUSP
ENSION
REAR A
XLE
AND REAR SUSPE
NSION
TI
RE
S
ROAD WHEE
L
BRAKE
STE
E
RING
Symptom
TIRES
Noise
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
×
×
Shudder
×
×
×
×
×
×
×
×
×
×
×
Poor quality ride
or handling
×
×
×
×
×
×
×
×
×
ROAD
WHEEL
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Shimmy, shudder
×
×
×
×
×
×
×
×
Poor quality ride
or handling
×
×
×
×
×
×
PRECAUTIONS
WT-45
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010218735
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Road Wheel
INFOID:0000000009483102
• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.
• Use Genuine NISSAN parts for the wheel nuts.
• Always adjusting the wheel balance prior to using them. For the balance weights, use Genuine NISSAN alu-
minum wheel weights.
• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing
dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-
gent if a detergent is needed.
• After driving on roads scattered with anti-icing salts, wash off the wheels completely.
• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them
from being trapped between the contact surfaces of wheel.
• Do not apply oil to nut and bolt threads.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст