Nissan Xterra. Instruction — part 625
PREPARATION
TM-13
< PREPARATION >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Commercial Service Tool
INFOID:0000000009485367
ST22490000
(
—
)
Adapter setting plate
Holding a adapter plate
ST33400001
(J-26082)
Drift
Installing oil seal
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
—
(J-46534)
Trim Tool Set
Removing trim components
Tool number
(TechMate No.)
Tool name
Description
ZZC0465D
NT086
AWJIA0483ZZ
Tool name
Description
Puller
Removing each bearing, gear and bushing
Pin punch
Removing and installing each retaining pin
Tip diameter: 6.0 mm (0.236 in) dia.
Power tool
Loosening nuts, screws and bolts
ZZB0823D
ZZA0815D
PIIB1407E
TM-14
< PREPARATION >
[6MT: FS6R31A]
PREPARATION
Puller
• Removing reverse synchronizer hub as-
sembly
• Removing reverse counter gear
• Removing reverse main gear
Drift
Removing counter end bearing
a: 32 mm (1.26 in) dia.
Tool name
Description
NT077
LCIA0362E
M/T OIL
TM-15
< PERIODIC MAINTENANCE >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PERIODIC MAINTENANCE
M/T OIL
Changing
INFOID:0000000009485368
DRAINING
1. Start the engine and let it run to warm up the transmission.
2. Stop the engine. Remove the transmission drain plug and drain the oil.
3. Set a gasket on the drain plug and install it to the transmission. Tighten the drain plug to the specified
CAUTION:
Do not reuse gasket.
FILLING
1. Remove the filler plug. Fill with new oil until oil level reaches the
specified limit near the filler plug hole as shown.
2. After refilling the oil, check oil level. Set a gasket to the filler
plug, then install it to the transmission. Tighten the filler plug to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
Checking
INFOID:0000000009485369
OIL LEAKAGE AND OIL LEVEL
1. Make sure that oil is not leaking from the transmission or around it.
2. Check oil level from the filler plug hole as shown.
CAUTION:
Do not start engine while checking oil level.
3. Set a gasket on the filler plug and install it to the transmission.
Tighten the filler plug to the specified torque. Refer to
CAUTION:
Do not reuse gasket.
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
PCIB0268E
PCIB0268E
TM-16
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
REAR OIL SEAL
REMOVAL AND INSTALLATION
REAR OIL SEAL
Removal and Installation
INFOID:0000000009485370
REMOVAL
1. Remove transfer assembly. Refer to
DLN-99, "Removal and Installation"
.
2. Remove rear oil seal using Tool.
CAUTION:
Do not damage OD gear case.
INSTALLATION
Installation is in the reverse order of removal.
• Drive the rear oil seal using Tool.
CAUTION:
Do not incline the rear oil seal during installation.
• Check the transmission oil level after installation. Refer to
.
Tool number
: KV381054S0 (J-34286)
PCIB1218E
Tool number
: ST33200000 (J-26082)
Dimension (A)
: -0.5 - 0.5 mm (-0.020 - 0.020 in)
PCIB1632E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст