Nissan Xterra. Instruction — part 56
AV-216
< PRECAUTION >
[NAVIGATION]
PRECAUTIONS
• Do not perform bypass wire connections for the repair parts. (The
spliced wire will become separated and the characteristics of
twisted line will be lost.)
Precaution for Work
INFOID:0000000009485319
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
PKIA0307E
AV
PREPARATION
AV-217
< PREPARATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009485320
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tools
INFOID:0000000009485321
Tool number
(TechMate No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
AV-218
< REMOVAL AND INSTALLATION >
[NAVIGATION]
AV CONTROL UNIT
REMOVAL AND INSTALLATION
AV CONTROL UNIT
Removal and Installation
INFOID:0000000009485322
REMOVAL
CAUTION:
• Remove battery terminal and AV control unit after a lapse of 30 seconds or more after turning the
ignition switch OFF.
• Before replacing AV control unit, perform "READ CONFIGURATION" to save current vehicle specifi-
cation. Refer to
AV-154, "ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT : Work Pro-
1. Disconnect the negative battery terminal. Refer to
PG-72, "Removal and Installation"
2. Remove cluster lid C. Refer to
IP-15, "Removal and Installation"
3. Remove the screws (A) from the bracket.
4. Remove the audio unit (1) from cluster lid C.
INSTALLATION
CAUTION:
When replacing AV control unit, perform "WRITE CONFIGURATION". Refer to
SERVICE WHEN REPLACING AV CONTROL UNIT : Work Procedure"
.
Installation is in the reverse order of removal.
ALNIA2930ZZ
AV
AUDIO AMP.
AV-219
< REMOVAL AND INSTALLATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
AUDIO AMP.
Removal and Installation
INFOID:0000000009485323
REMOVAL
NOTE:
Do not remove the RH front seat from the vehicle.
1. Remove the RH front seat bolts, disconnect the harness connectors from the RH front seat. Refer to
2. Tilt the RH front seat back to access the audio amp. (1) and
remove the audio amp. kick shield screws (C).
: Front
3. Disconnect the harness connectors (A) from the audio amp. and
remove the audio amp. (1) from the bracket (2).
4. Remove the audio amp. bracket screws (B) and bracket (2).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1248ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст