Nissan Xterra. Instruction — part 573
AXLE OIL SEAL
RAX-25
< UNIT REMOVAL AND INSTALLATION >
[M226]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
AXLE OIL SEAL
Removal and Installation
INFOID:0000000009484518
The axle oil seal must be replaced every time the axle shaft is removed and installed. Refer to
CAUTION:
Do not reuse the axle oil seal.
RAX-26
< SERVICE DATA AND SPECIFICATIONS (SDS)
[M226]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Axle Bearing
INFOID:0000000009484519
Bearing ring retainer axle journal diameter (minimum)
39.726 mm (1.5640 in) minimum
RSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
RSU
A
B
RSU
N
O
P
CONTENTS
REAR SUSPENSION
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Rear Suspension . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
REAR SUSPENSION ASSEMBLY . . . . . .
On-Vehicle Inspection and Service . . . . . . ...
STABILIZER BAR . . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
REAR SUSPENSION ASSEMBLY . . . . .
Component . . . . . . . . . . . . . . . ...
UNIT REMOVAL AND INSTALLATION . ...
SHOCK ABSORBER . . . . . . . . . . .
Removal and Installation . . . . . . . . . . ..
Disposal . . . . . . . . . . . . . . . . ....
LEAF SPRING . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
STABILIZER BAR . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
General Specification (Rear) . . . . . . . . ...
RSU-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010203654
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Rear Suspension
INFOID:0000000009484400
• When installing rubber parts, final tightening must be carried out under unladen condition* with tires on
ground.
* Fuel, radiator coolant, and engine oil are full. Spare tire, jack, hand tools, and mats are in their designated
positions.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст