Nissan Xterra. Instruction — part 202
DLK-50
< DTC/CIRCUIT DIAGNOSIS >
WARNING CHIME FUNCTION
WARNING CHIME FUNCTION
Description
INFOID:0000000009485061
Performs operation method guide and warning with buzzer.
Component Function Check
INFOID:0000000009485062
1.
CHECK FUNCTION
With CONSULT
Check the operation of "INSIDE BUZZER" in the Active Test. Refer to
.
Is the inspection result normal?
Yes
>> Warning buzzer into combination meter is OK.
No
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009485063
1.
CHECK METER BUZZER CIRCUIT
The inoperative warning chime is contained inside the combination meter. Replace combination meter. Refer
to
MWI-84, "Removal and Installation"
.
>> Inspection End.
HAZARD FUNCTION
DLK-51
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HAZARD FUNCTION
Description
INFOID:0000000009485064
Perform answer-back for each operation with number of blinks.
Component Function Check
INFOID:0000000009485065
1.
CHECK FUNCTION
Check hazard warning lamp "FLASHER" in ACTIVE TEST.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009485066
1.
CHECK HAZARD SWITCH CIRCUIT
Operate the hazard lights by turning ON the hazard warning switch.
Do the lights operate normally?
YES
>> Replace the BCM. Refer to
BCS-50, "Removal and Installation"
NO
>> Repair or replace hazard warning switch circuit. Refer to
.
DLK-52
< DTC/CIRCUIT DIAGNOSIS >
KEY SWITCH (BCM INPUT)
KEY SWITCH (BCM INPUT)
Diagnosis Procedure
INFOID:0000000009485067
Regarding Wiring Diagram information, refer to
.
1.
CHECK KEY SWITCH INPUT SIGNAL
With CONSULT
Check key switch "KEY ON SW" in DATA MONITOR mode with CONSULT. Refer to
CONSULT Function (BCM - DOOR LOCK)"
.
• When key is inserted to ignition key cylinder:
• When key is removed from ignition key cylinder:
Without CONSULT
Check voltage between BCM connector M18 terminal 37 and
ground.
Is the inspection result normal?
YES
>> Key switch (insert) circuit is OK.
NO
>> GO TO 2
2.
CHECK KEY SWITCH (INSERT)
1. Turn ignition switch OFF.
2. Disconnect key switch connector.
3. Check continuity between key switch terminals.
Is the inspection result normal?
YES
>> Repair or replace harness or fuse.
NO
>> Replace key switch.
KEY ON SW
: ON
KEY ON SW
: OFF
Connec-
tor
Terminal
Condition
Voltage (V)
(+)
(–)
M18
37
Ground
Key is inserted.
Battery voltage
Key is removed.
0
LIIA0567E
Terminals
Condition
Continuity
1 – 2
Key is inserted.
Yes
Key is removed.
No
HEADLAMP FUNCTION
DLK-53
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HEADLAMP FUNCTION
Diagnosis Procedure
INFOID:0000000009485068
1.
CHECK HEADLAMP OPERATION
Do headlamps operate with headlamp switch?
YES or NO
YES
>> Headlamp circuit is OK.
NO
>> Check headlamp circuit. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст