Nissan Xterra. Instruction — part 130
C1130, C1131, C1132, C1133, C1136 ENGINE SIGNAL
BRC-177
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1130, C1131, C1132, C1133, C1136 ENGINE SIGNAL
Description
INFOID:0000000009482793
ABS actuator and electric unit (control unit) and ECM exchange the engine signal with CAN communication
line.
DTC Logic
INFOID:0000000009482794
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
BRC-177, "Diagnosis Procedure"
NO
>> Inspection End
Diagnosis Procedure
INFOID:0000000009482795
1.
CHECK ENGINE SYSTEM
1. Perform ECM self-diagnosis. Repair or replace items indicated, then perform ECM self-diagnosis again.
2. Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
.
Is any item indicated on the self-diagnosis display?
YES
>> Repair or replace the affected part.
NO
>> Inspection End
DTC
Display item
Malfunction detected condition
Possible cause
C1130
ENGINE SIGNAL 1
Based on the signal from ECM, ABS actuator and electric
unit (control unit) judges that engine fuel cut system is
malfunctioning.
• Harness or connector
• ABS actuator and electric unit
(control unit)
• ECM
• CAN communication line
C1131
ENGINE SIGNAL 2
C1132
ENGINE SIGNAL 3
C1133
ENGINE SIGNAL 4
C1136
ENGINE SIGNAL 6
Self-diagnosis results
ENGINE SIGNAL 1
ENGINE SIGNAL 2
ENGINE SIGNAL 3
ENGINE SIGNAL 4
ENGINE SIGNAL 6
BRC-178
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C1140 ACTUATOR RLY
C1140 ACTUATOR RLY
Description
INFOID:0000000009482796
Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and
electric unit (control unit).
DTC Logic
INFOID:0000000009482797
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
BRC-178, "Diagnosis Procedure"
.
NO
>> Inspection End
Diagnosis Procedure
INFOID:0000000009482798
Regarding Wiring Diagram information, refer to
BRC-211, "Wiring Diagram - WITH HILL DESCENT CON-
1.
CONNECTOR INSPECTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or
replace terminal.
4. Reconnect connectors and then perform the self-diagnosis. Refer to
.
Is any item indicated on the self-diagnosis display?
YES
>> GO TO 2
NO
>> Poor connection of connector terminal. Repair or replace connector.
2.
CHECK SOLENOID, VDC SWITCH-OVER VALVE AND ACTUATOR RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check voltage between ABS actuator and electric unit (control unit) connector E125 terminal 32 and
ground.
Is the inspection result normal?
YES
>> GO TO 3
DTC
Display item
Malfunction detected condition
Possible cause
C1140
ACTUATOR RLY
ABS actuator relay or circuit malfunction.
• Harness or connector
• ABS actuator and electric unit
(control unit)
Self-diagnosis results
ACTUATOR RLY
ABS actuator and electric unit (control unit)
—
Voltage
Connector
Terminal
E125
32
Ground
Battery voltage
C1140 ACTUATOR RLY
BRC-179
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
NO
>> Repair or replace malfunctioning components.
3.
CHECK SOLENOID, VDC SWITCH-OVER VALVE AND ACTUATOR RELAY GROUND CIRCUIT
Check continuity between ABS actuator and electric unit (control unit) connector E125 terminals 16, 47 and
ground.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-234, "Removal and Installa-
.
NO
>> Repair or replace malfunctioning components.
Component Inspection
INFOID:0000000009482799
1.
CHECK ACTIVE TEST
1. On “ACTIVE TEST”, select “ABS MOTOR”.
2. Touch On and Off on screen. Make sure motor relay and actuator relay operates as shown in table below.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Go to diagnosis procedure. Refer to
BRC-178, "Diagnosis Procedure"
.
Special Repair Requirement
INFOID:0000000009482800
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to
BRC-122, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-
>> GO TO 2
2.
CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
BRC-123, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
ABS actuator and electric unit (control unit)
—
Continuity
Connector
Terminal
E125
16, 47
Ground
Yes
Operation
On
Off
MOTOR RELAY
On
Off
ACTUATOR RLY
On
On
BRC-180
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C1143, C1144 STEERING ANGLE SENSOR
C1143, C1144 STEERING ANGLE SENSOR
Description
INFOID:0000000009482801
The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel,
and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication.
DTC Logic
INFOID:0000000009482802
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
BRC-180, "Diagnosis Procedure"
.
NO
>> Inspection End
Diagnosis Procedure
INFOID:0000000009482803
Regarding Wiring Diagram information, refer to
BRC-211, "Wiring Diagram - WITH HILL DESCENT CON-
1.
CONNECTOR INSPECTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Disconnect steering angle sensor connector.
4. Check terminals for deformation, disconnection, looseness, and so on. If any malfunction is found, repair
or replace terminals.
5. Reconnect connectors and then perform the self-diagnosis. Refer to
.
Is any item indicated on the self-diagnosis display?
YES
>> GO TO 2
NO
>> Poor connection of connector terminals. Repair or replace connector.
2.
CHECK STEERING ANGLE SENSOR HARNESS
DTC
Display item
Malfunction detected condition
Possible cause
C1143
ST ANG SEN CIRCUIT
Neutral position of steering angle sensor is dislocated, or
the steering angle sensor is malfunctioning.
• Harness or connector
• Steering angle sensor
• ABS actuator and electric unit
(control unit)
C1144
ST ANG SEN SIGNAL
Neutral position of steering angle sensor is not finished.
Self-diagnosis results
ST ANG SEN CIRCUIT
ST ANG SEN SIGNAL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст