Nissan Xterra. Instruction — part 587
FRONT SEAT
SE-27
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
FRONT SEAT
Exploded View
INFOID:0000000009483055
Driver Seat
AWJIA0555GB
SE-28
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
1.
Locking headrest guide
2.
Headrest guide
3.
Headrest
4.
Seatback assembly with side air bag 5.
Lumbar support lever (if equipped)
6.
Seat cushion trim
7.
Seat cushion pad
8.
Seat cushion assembly
9.
Seat cushion frame
10. Seat cushion rear finisher
11. Leg cover
12. Seat belt buckle
13. Seat cushion inner finisher
14. Driver seat slide assembly
15. Seat cushion outer finisher
16. Seatback recline release lever
17. Outer pedestal finisher
18. Seat cushion adjusting knob clips (if
equipped)
19. Seat cushion adjusting knobs (if
equipped)
FRONT SEAT
SE-29
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Passenger Seat
AWJIA1275ZZ
1.
Seatback board
2.
Locking headrest guide
3.
Headrest guide
4.
Headrest
5.
Front seatback lever (if equipped)
6.
Seat cushion assembly
7.
Seatback assembly with side air bag 8.
Fold flat seat frame slide assembly
9.
Inboard reclining arm outer cover
10. Inboard reclining arm inner cover
11. Outboard reclining arm inner cover
12. Outboard reclining arm outer cover
13. Seat cushion rear finisher
14. Fold flat seat frame
15. Seat cushion outer finisher
SE-30
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Disassembly and Assembly
INFOID:0000000009483056
SEATBACK
Disassembly
CAUTION:
• Only complete seatback assemblies can be replaced.
• When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
1. Remove the seatback assembly. Refer to
SE-21, "Removal and Installation"
2. Remove the headrest.
3. From inside of the seatback, squeeze the headrest holder tabs
at the base of the stay pipe and pull upward to remove.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
4. Remove the snap ring and the lumbar support lever knob (if
equipped).
Assembly
Assembly is in the reverse order of disassembly.
SEAT CUSHION TRIM AND PAD
Disassembly
CAUTION:
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
• When removed, the passenger seat cushion must always be placed pan side UP to prevent damage.
• During installation, the wire harness clips must be reinstalled in the holes they were originally in. Do
not add additional clips.
• The Occupant Classification System control module can only be replaced as part of the seat cushion
assembly.
1. Remove the recline release lever.
2. Remove four seat cushion bolts and the seat cushion assembly.
3. On the drivers seat only, remove the seat cushion trim and pad.
4. On the drivers seat only, remove the hog rings to separate the trim cover from the pad.
Assembly
16. Outer pedestal finisher
17. Instruction seat frame slide assembly
18. Seat cushion inner cover
19. Leg cover
20. Recline release lever
21. Bolt cap
LRS023
PIIA1156E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст