Nissan Xterra. Instruction — part 136
VDC OFF INDICATOR LAMP
BRC-201
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
VDC OFF INDICATOR LAMP
Description
INFOID:0000000009482853
×: ON –: OFF
Component Function Check
INFOID:0000000009482854
1.
VDC OFF INDICATOR LAMP OPERATION CHECK 1
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Go to diagnosis procedure. Refer to
BRC-201, "Diagnosis Procedure"
.
2.
VDC OFF INDICATOR LAMP OPERATION CHECK 2
Check that the VDC OFF indicator lamp in the combination meter turns ON/OFF correctly when operating the
VDC OFF switch.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Check VDC OFF switch. Refer to
BRC-196, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009482855
1.
CHECK VDC OFF SWITCH
Check that the VDC OFF indicator lamp in the combination meter turns ON/OFF correctly when operating the
VDC OFF switch.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check VDC OFF switch. Refer to
BRC-196, "Diagnosis Procedure"
.
2.
CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Check items displayed by self-diagnosis.
3.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-234, "Removal and Installa-
.
NO
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
Condition
VDC OFF indicator lamp
Ignition switch OFF
–
For 2 seconds after turning ON ignition switch
×
2 seconds later after turning ON ignition switch
–
VDC OFF switch turned ON. (VDC function is OFF.)
×
VDC/TCS function is malfunctioning.
–
ABS function is malfunctioning.
–
EBD function is malfunctioning.
–
BRC-202
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
VDC OFF INDICATOR LAMP
Special Repair Requirement
INFOID:0000000009482856
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to
BRC-122, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-
>> GO TO 2
2.
CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
BRC-123, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
SLIP INDICATOR LAMP
BRC-203
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SLIP INDICATOR LAMP
Description
INFOID:0000000009482857
×: ON –: OFF
Component Function Check
INFOID:0000000009482858
1.
CHECK SLIP INDICATOR LAMP OPERATION
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Go to diagnosis procedure. Refer to
BRC-203, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009482859
1.
CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check items displayed by self-diagnosis.
2.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-234, "Removal and Installa-
.
NO
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
Special Repair Requirement
INFOID:0000000009482860
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to
BRC-122, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-
>> GO TO 2
2.
CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
BRC-123, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
Condition
SLIP indicator lamp
Ignition switch OFF
–
For 2 seconds after turning ON ignition switch
×
2 seconds later after turning ON ignition switch
–
VDC/TCS function is malfunctioning.
×
ABS function is malfunctioning.
×
EBD function is malfunctioning.
×
BRC-204
< ECU DIAGNOSIS INFORMATION >
[TYPE 2]
APPLICATION NOTICE
ECU DIAGNOSIS INFORMATION
APPLICATION NOTICE
Application Notice
INFOID:0000000009482861
Service information
Remarks
TYPE 1
VDC/TCS/ABS
TYPE 2
HILL DESCENT CONTROL/HILL START ASSIST/VDC/TCS/ABS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст