Nissan Xterra. Instruction — part 609
STEERING WHEEL
ST-11
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
REMOVAL AND INSTALLATION
STEERING WHEEL
Removal and Installation
INFOID:0000000009483749
REMOVAL
1. Set the front wheels in the straight-ahead position.
2. Remove the driver air bag module. Refer to
SR-11, "Removal and Installation"
.
3. Disconnect the harness connectors from the steering wheel switches.
4. Remove the steering wheel center nut.
5. Remove the steering wheel using Tools (A and B).
6. Inspect the steering wheel near the puller holes for damage. If
damage is found, replace the steering wheel.
• Remove the steering wheel rear cover and steering wheel
switches, if required.
CAUTION:
Place a piece of tape across the spiral cable so it will not be
rotated out of position.
INSTALLATION
Installation is in the reverse order of removal.
• Align spiral cable correctly when installing steering wheel. Make
sure that the spiral cable is in the neutral position. The neutral
position is detected by turning left 2.5 revolutions from the right
end position and ending with the locating pin at the top.
• After installation, perform the steering angle sensor adjustment.
Refer to
BRC-12, "ADJUSTMENT OF STEERING ANGLE SEN-
SOR NEUTRAL POSITION : Special Repair Requirement"
(TYPE
1),
BRC-122, "ADJUSTMENT OF STEERING ANGLE SENSOR
NEUTRAL POSITION : Special Repair Requirement"
(TYPE 2) for
steering angle sensor adjustment.
• After the work is completed, perform self-diagnosis to make sure
no malfunction is detected. Refer to
.
• Tighten steering wheel center nut to specification. Refer to
ST-11, "Removal and Installation"
CAUTION:
• The spiral cable may snap due to steering operation if the cable is not installed in the correct posi-
tion.
• With the steering linkage disconnected, the cable may snap by turning the steering wheel beyond
the limited number of turns. The spiral cable can be turned counterclockwise about 2.5 turns from
the neutral position.
Tool number
(A): KV481J0010 (J-1859A)
(B): KV481J0020 (J-42578)
WHIA0124E
PHIA0275E
ST-12
< REMOVAL AND INSTALLATION >
STEERING COLUMN
STEERING COLUMN
Removal and Installation
INFOID:0000000009483750
CAUTION:
• Do not exert any axial load or impact to the steering column.
• Do not move the steering gear while the steering column assembly is removed.
• Anytime the ignition switch has been removed or installed, the keys must be re-registered in the
BCM. Refer to CONSULT Immobilizer mode and follow the on-screen instructions.
REMOVAL
1. Remove the spiral cable with the combination switches attached from the steering column assembly.
SR-13, "Removal and Installation"
.
2. Remove the instrument lower panel LH. Refer to
.
3. Remove the key interlock cable from the steering column (if equipped). Refer to
.
1.
Driver air bag module
2.
Steering wheel center nut
3.
Steering wheel
4.
Combination switch and spiral
cable
5.
Steering column assembly and
ignition switch
6.
Collar
7.
Hole cover seal
8.
Clamp
9.
Hole cover plate
10. Hole cover
11. Upper joint
12. Upper shaft
13. Boot clamp
14. Lower joint shaft
15. Boot and clips (plastic)
AWGIA0198GB
STEERING COLUMN
ST-13
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
4. Remove the lock nut and bolt from the upper joint, then separate
the upper joint from the upper shaft.
CAUTION:
Do not reuse the lock nut.
5. Remove the three nuts and bolt from the steering column
assembly, then remove the steering column assembly from the
steering member.
6. Remove the hole cover seal and clamp.
7. Remove the hole cover nuts, then remove the hole cover from
the dash panel.
8. Remove the bolt from the lower joint of the lower joint shaft, then
remove the lower joint shaft from the vehicle.
CAUTION:
Do not damage the lower joint.
INSPECTION AFTER REMOVAL
• Check for damage to the steering column jacket tube. If damage is found, replace the steering column with a
new one.
CAUTION:
• Do not exert any axial load or impact to the steering column.
• Replace the column if it is depleted of grease, worn, damaged, or if any scratches or coating sepa-
ration is present on the shaft seal area.
• If the vehicle has been in a collision, or if noises are heard coming
from the steering column, check column length. If out of specifica-
tion, replace the steering column as an assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
LGIA0027E
LGIA0028E
LGIA0029E
Steering column
length (L)
.
AWGIA0147ZZ
ST-14
< REMOVAL AND INSTALLATION >
STEERING COLUMN
When installing the steering column, finger-tighten all of the lower bracket and joint bolts; then tighten
them to specification. Do not apply undue stress to the steering column.
NOTE:
• With the wheels in the straight ahead position, align the slit of the
lower joint with the projection on the dust cover. Insert the joint until
surface (A) contacts surface (B).
• After installation, inspect the steering column for proper operation.
INSPECTION AFTER INSTALLATION
• Check the tilt device for proper tilt range.
• Check that the steering wheel turns smoothly to the left and right
locks.
• Check that the number of turns are the same from the straight-for-
ward position to the left and right locks.
• Check that the steering wheel is in the neutral position when driv-
ing straight ahead.
SST491C
Tilt range (A)
: Refer to
WGIA0083E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст