Nissan Xterra. Instruction — part 215
DLK-102
< PREPARATION >
PREPARATION
(TechMate No.)
Tool name
Description
(J-39565)
Engine Ear
Locating the noise
SIIA0995E
HOOD
DLK-103
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOVAL AND INSTALLATION
HOOD
Fitting Adjustment
INFOID:0000000009485089
CLEARANCE AND SURFACE HEIGHT ADJUSTMENT
1. Remove the front grille. Refer to
EXT-19, "Removal and Installation"
2. Loosen the hood lock assembly and adjust the rubber bumpers until the surface height of the hood
becomes 1 mm (0.04 in) lower than the fender.
3. Engage the hood striker and temporarily tighten.
4. Check the lock and striker for looseness.
1.
Hood
2.
Front grille
3.
Front fender
4.
Front combination lamp
D.
6.0
± 2.3 mm (0.24 ± 0.09 in)
E.
0.0
± 2.4 mm (0.0 ± 0.09 in)
F.
4.6
± 1.0 mm (0.18 ± 0.04 in)
G.
0.0
± 1.0 mm (0.0 ± 0.04 in)
H.
6.0
± 2.0 mm (0.24 ± 0.08 in)
J.
0.0
± 2.0 mm (0.0 ± 0.08 in)
AWKIA0486ZZ
DLK-104
< REMOVAL AND INSTALLATION >
HOOD
5. Tighten the bolts to specification.
6. Adjust the surface height of the hood according to the fitting standard dimension by rotating right and left
rubber bumpers.
7. Install the front grille. Refer to
EXT-19, "Removal and Installation"
.
HOOD LOCK ADJUSTMENT
1. Remove the front grille. Refer to
EXT-19, "Removal and Installation"
2. Move the hood lock to the left or right so that striker center is vertically aligned with hood lock center
(when viewed from vehicle front).
3. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height or by pressing it lightly approx.
29 N (3 kg-f, 6.5 ft-lb).
CAUTION:
Do not drop the hood from 300 mm (11.81 in) height or
higher.
4. After adjusting hood lock, tighten the lock bolts to the specified
torque.
5. Install the front grille. Refer to
EXT-19, "Removal and Installation"
.
Removal and Installation of Hood Assembly
INFOID:0000000009485090
REMOVAL
1. Support the hood striker with suitable tool to prevent it from falling.
CAUTION:
Two technicians should be used to avoid damaging the hood during removal.
2. Remove the hinge nuts from the hood to remove the hood assembly.
LIIA1696E
LIIA1701E
WIIA1055E
HOOD
DLK-105
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation of Hood Lock Control
INFOID:0000000009485091
REMOVAL
1. Remove the bolts and the hood lock assembly.
2. Disconnect the hood lock control cable from the hood lock, and unclip it from the radiator core support
upper and hoodledge.
3. Remove the bolts and the hood release handle.
4. Separate the grommet from the lower dash panel. Pull the hood lock control cable out through the passen-
ger compartment.
CAUTION:
While pulling, be careful not to damage the outside of the hood lock control cable.
INSTALLATION
1. Pull the hood lock control cable through the lower dash panel hole into the engine room.
1.
Hood lock assembly
2.
Hood lock control cable
WIIA0775E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст