Nissan Xterra. Instruction — part 133
C1164, C1165, C1166, C1167 CV/SV SYSTEM
BRC-189
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1164, C1165, C1166, C1167 CV/SV SYSTEM
Description
INFOID:0000000009482820
CV1, CV2 (CUT VALVE)
The cut valve shuts off the normal brake fluid path from the master cylinder, when VDC/TCS is activated.
SV1, SV2 (SUCTION VALVE)
The suction valve supplies the brake fluid from the master cylinder to the pump, when VDC/TCS is activated.
DTC Logic
INFOID:0000000009482821
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
BRC-189, "Diagnosis Procedure"
NO
>> Inspection End
Diagnosis Procedure
INFOID:0000000009482822
Regarding Wiring Diagram information, refer to
BRC-211, "Wiring Diagram - WITH HILL DESCENT CON-
1.
CONNECTOR INSPECTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or
replace terminal.
4. Reconnect connectors and then perform the self-diagnosis. Refer to
.
Is any item indicated on the self-diagnosis display?
DTC
Display item
Malfunction detected condition
Possible cause
C1164
CV1
VDC switch-over solenoid valve (CV1) on the primary
side is open circuit or shorted, or the control line is open
or shorted to the power supply or the ground.
• Harness or connector
• ABS actuator and electric unit
(control unit)
C1165
CV2
VDC switch-over solenoid valve (CV2) on the primary
side is open circuit or shorted, or the control line is open
or shorted to the power supply or the ground.
C1166
SV1
VDC switch-over solenoid valve (SV1) on the primary
side is open circuit or shorted, or the control line is open
or shorted to the power supply or the ground.
C1167
SV2
VDC switch-over solenoid valve (SV2) on the primary
side is open circuit or shorted, or the control line is open
or shorted to the power supply or the ground.
Self-diagnosis results
CV1
CV2
SV1
SV2
BRC-190
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C1164, C1165, C1166, C1167 CV/SV SYSTEM
YES
>> GO TO 2
NO
>> Poor connection of connector terminal. Repair or replace connector.
2.
CHECK SOLENOID, VDC SWITCH-OVER VALVE AND ACTUATOR RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check voltage between ABS actuator and electric unit (control unit) connector E125 terminal 32 and
ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace malfunctioning components.
3.
CHECK SOLENOID, VDC SWITCH-OVER VALVE AND ACTUATOR RELAY GROUND CIRCUIT
Check continuity between ABS actuator and electric unit (control unit) connector E125 terminals 16, 47 and
ground.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-234, "Removal and Installa-
.
NO
>> Repair or replace malfunctioning components.
Component Inspection
INFOID:0000000009482823
1.
CHECK ACTIVE TEST
1. Select each test menu item on “ACTIVE TEST”.
2. On the display, touch “Up”, “ACT UP”, and “ACT KEEP”, and check that the system operates as shown in
the table below.
*: ON for 1 to 2 seconds after the touch, and then OFF
Is the inspection result normal?
YES
>> Inspection End
NO
>> Go to diagnosis procedure. Refer to
BRC-189, "Diagnosis Procedure"
Special Repair Requirement
INFOID:0000000009482824
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
ABS actuator and electric unit (control unit)
—
Voltage
Connector
Terminal
E125
32
Ground
Battery voltage
ABS actuator and electric unit (control unit)
—
Continuity
Connector
Terminal
E125
16, 47
Ground
Yes
Operation
ABS solenoid valve (ACT)
Up
ACT UP
ACT KEEP
FR RH ABS SOLENOID (ACT)
FR RH IN SOL
Off
Off
Off
FR RH OUT SOL
Off
Off
Off
FR LH ABS SOLENOID (ACT)
FR LH IN SOL
Off
Off
Off
FR LH OUT SOL
Off
Off
Off
RR RH ABS SOLENOID (ACT)
RR RH IN SOL
Off
Off
Off
RR RH OUT SOL
Off
Off
Off
RR LH ABS SOLENOID (ACT)
RR LH IN SOL
Off
Off
Off
RR LH OUT SOL
Off
Off
Off
C1164, C1165, C1166, C1167 CV/SV SYSTEM
BRC-191
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to
BRC-122, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-
>> GO TO 2
2.
CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
BRC-123, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
BRC-192
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C1187 DIFFERENTIAL LOCK CONTROL UNIT
C1187 DIFFERENTIAL LOCK CONTROL UNIT
Description
INFOID:0000000009482825
The differential lock control unit is connected to the ABS actuator and electric unit (control unit) via CAN lines.
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
DTC Logic
INFOID:0000000009482826
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
BRC-192, "Diagnosis Procedure"
.
NO
>> Inspection End
Diagnosis Procedure
INFOID:0000000009482827
1.
CONNECTOR INSPECTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check terminals for deformation, disconnection, looseness, and so on. If any malfunction is found, repair
or replace terminals.
4. Reconnect connector and perform self-diagnosis. Refer to
BRC-145, "CONSULT Function (ABS)"
Is above displayed on the self-diagnosis display?
YES
>> Refer to
LAN-14, "Trouble Diagnosis Flow Chart"
NO
>> Inspection End
DTC
Display item
Malfunction detected condition
Possible cause
C1187
ABS DIFLOCK CONTROL-
LER NG
Differential lock controller malfunction.
• Harness or connector
• CAN communication line
• Differential lock control unit
• ABS actuator and electric unit
(control unit)
Self-diagnosis results
ABS DIFLOCK CONTROLLER NG
Self-diagnosis results
ABS DIFLOCK CONTROLLER NG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст