Nissan Frontier. Instruction — part 487
DIAGNOSIS SYSTEM (ECM)
EC-519
< SYSTEM DESCRIPTION >
[VQ40DE FOR USA AND CANADA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
How to Erase DTC and 1st Trip DTC
NOTE:
• If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10
seconds and then turn it ON (engine stopped) again.
• If the DTC is not for A/T related items (see
), skip step 1.
1. Erase DTC in TCM. Refer to
2. Select “ENGINE” with CONSULT.
3. Select “SELF-DIAG RESULTS”.
4. Touch “ERASE”. (DTC in ECM will be erased.)
Freeze Frame Data and 1st Trip Freeze Frame Data
*: The items are the same as those of 1st trip freeze frame data.
DATA MONITOR MODE
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitored Item
For reference values of the following items, refer to
EC-528, "CONSULT Reference Value in Data Monitor
.
Freeze frame data
item*
Description
DIAG TROUBLE
CODE
[PXXXX]
• The engine control component part/control system has a trouble code, that is displayed as PXXXX. (Refer
.)
FUEL SYS-B1
• “Fuel injection system status” at the moment a malfunction is detected is displayed.
• One of in the following made is displayed.
Mode2: Open loop due to detected system malfunction
Mode3: Open loop due to driving conditions (power enrichment, deceleration enleanment)
Mode4: Closed loop - using oxygen sensor(s) as feedback for fuel control
Mode5: Open loop - has not yet satisfied condition to go to closed loop
FUEL SYS-B2
CAL/LD VALUE [%]
• The calculated load value at the moment a malfunction is detected is displayed.
COOLANT TEMP [
°C]
or [
°F]
• The engine coolant temperature at the moment a malfunction is detected is displayed.
L-FUEL TRM-B1 [%]
• “Long-term fuel trim” at the moment a malfunction is detected is displayed.
• The long-term fuel trim indicates much more gradual feedback compensation to the base fuel schedule than
short-term fuel trim.
L-FUEL TRM-B2 [%]
S-FUEL TRM-B1 [%]
• “Short-term fuel trim” at the moment a malfunction is detected is displayed.
• The short-term fuel trim indicates dynamic or instantaneous feedback compensation to the base fuel sched-
ule.
S-FUEL TRM-B2 [%]
ENGINE SPEED [rpm] • The engine speed at the moment a malfunction is detected is displayed.
VEHICL SPEED [km/
h] or [mph]
• The vehicle speed at the moment a malfunction is detected is displayed.
ABSOL TH-P/S [%]
• The throttle valve opening angle at the moment a malfunction is detected is displayed.
B/FUEL SCHDL
[msec]
• The base fuel schedule at the moment a malfunction is detected is displayed.
INT/A TEMP SE [
°C]
or [
°F]
• The intake air temperature at the moment a malfunction is detected is displayed.
INT MANI PRES [kPa]
• Always a certain value is displayed.
• These items are displayed but are not applicable to this model.
COMBUST CONDI-
TION
EC-520
< SYSTEM DESCRIPTION >
[VQ40DE FOR USA AND CANADA]
DIAGNOSIS SYSTEM (ECM)
Monitored item
Unit
Description
Remarks
ENG SPEED
rpm
• Indicates the engine speed computed from the sig-
nal of the crankshaft position sensor (POS) and
camshaft position sensor (PHASE).
• Accuracy becomes poor if engine speed
drops below the idle rpm.
• If the signal is interrupted while the en-
gine is running, an abnormal value may
be indicated.
MAS A/F SE-B1
V
• The signal voltage of the mass air flow sensor is
displayed.
• When the engine is stopped, a certain
value is indicated.
• When engine is running specification
range is indicated in “SPEC”.
B/FUEL SCHDL
ms
• “Base fuel schedule” indicates the fuel injection
pulse width programmed into ECM, prior to any
learned on board correction.
• When engine is running specification
range is indicated in “SPEC”.
A/F ALPHA-B1
%
• The mean value of the air-fuel ratio feedback cor-
rection factor per cycle is indicated.
• When the engine is stopped, a certain
value is indicated.
• When engine is running specification
range is indicated in “SPEC”.
• This data also includes the data for the
air-fuel ratio learning control.
A/F ALPHA-B2
%
COOLANT TEMP/S
°C or °F
• The engine coolant temperature (determined by
the signal voltage of the engine coolant tempera-
ture sensor) is displayed.
• When the engine coolant temperature
sensor is open or short-circuited, ECM
enters fail-safe mode. The engine cool-
ant temperature determined by the ECM
is displayed.
A/F SEN1 (B1)
V
• The A/F signal computed from the input signal of
the Air fuel ratio (A/F) sensor 1 is displayed.
A/F SEN1 (B2)
V
HO2S2 (B1)
V
• The signal voltage of the heated oxygen sensor 2
is displayed.
HO2S2 (B2)
V
HO2S2 MNTR(B1)
RICH/
LEAN
• Display of heated oxygen sensor 2 signal:
RICH: Means the amount of oxygen after three way
catalyst is relatively small.
LEAN: Means the amount of oxygen after three
way catalyst is relatively large.
• When the engine is stopped, a certain
value is indicated.
HO2S2 MNTR(B2)
RICH/
LEAN
VHCL SPEED SE
km/h or
mph
• The vehicle speed computed from the vehicle
speed signal sent from combination meter is dis-
played.
BATTERY VOLT
V
• The power supply voltage of ECM is displayed.
ACCEL SEN 1
V
• The accelerator pedal position sensor signal volt-
age is displayed.
• ACCEL SEN 2 signal is converted by
ECM internally. Thus, it differs from ECM
terminal voltage signal.
ACCEL SEN 2
V
TP SEN 1-B1
V
• The throttle position sensor signal voltage is dis-
played.
• THRTL SEN 2 signal is converted by
ECM internally. Thus, it differs from ECM
terminal voltage signal.
TP SEN 2-B1
V
FUEL T/TMP SE
°C or °F
• The fuel temperature (determined by the signal
voltage of the fuel tank temperature sensor) is dis-
played.
INT/A TEMP SE
°C or °F
• The intake air temperature (determined by the sig-
nal voltage of the intake air temperature sensor) is
indicated.
EVAP SYS PRES
V
FUEL LEVEL SE
V
START SIGNAL
ON/OFF
• Indicates start signal status [ON/OFF] computed by
the ECM according to the signals of engine speed
and battery voltage.
• After starting the engine, [OFF] is dis-
played regardless of the starter signal.
DIAGNOSIS SYSTEM (ECM)
EC-521
< SYSTEM DESCRIPTION >
[VQ40DE FOR USA AND CANADA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
CLSD THL POS
ON/OFF
• Indicates idle position [ON/OFF] computed by ECM
according to the accelerator pedal position sensor
signal.
AIR COND SIG
ON/OFF
• Indicates [ON/OFF] condition of the air conditioner
switch as determined by the air conditioner signal.
P/N POSI SW
ON/OFF
• Indicates [ON/OFF] condition from the park/neutral
position (PNP) signal.
PW/ST SIGNAL
ON/OFF
• [ON/OFF] condition of the power steering system
(determined by the signal voltage of the power
steering pressure sensor signal) is indicated.
LOAD SIGNAL
ON/OFF
• Indicates [ON/OFF] condition from the electrical
load signal.
ON: Rear window defogger switch is ON and/or
lighting switch is in 2nd position.
OFF: Both rear window defogger switch and light-
ing switch are OFF.
IGNITION SW
ON/OFF
• Indicates [ON/OFF] condition from ignition switch
signal.
HEATER FAN SW
ON/OFF
• Indicates [ON/OFF] condition from the heater fan
switch signal.
BRAKE SW
ON/OFF
• Indicates [ON/OFF] condition from the stop lamp
switch signal.
INJ PULSE-B1
msec
• Indicates the actual fuel injection pulse width com-
pensated by ECM according to the input signals.
• When the engine is stopped, a certain
computed value is indicated.
INJ PULSE-B2
msec
IGN TIMING
BTDC
• Indicates the ignition timing computed by ECM ac-
cording to the input signals.
• When the engine is stopped, a certain
value is indicated.
CAL/LD VALUE
%
• Calculated load value indicates the value of the
current air flow divided by peak air flow.
MASS AIRFLOW
g/s
• Indicates the mass air flow computed by ECM ac-
cording to the signal voltage of the mass air flow
sensor.
PURG VOL C/V
%
• Indicates the EVAP canister purge volume control
solenoid valve control value computed by the ECM
according to the input signals.
• The opening becomes larger as the value increas-
es.
INT/V TIM(B1)
°CA
• Indicates [
°CA] of intake camshaft advanced angle.
INT/V TIM(B2)
°CA
INT/V SOL(B1)
%
• The control condition of the intake valve timing con-
trol solenoid valve (determined by ECM according
to the input signals) is indicated.
• The advance angle becomes larger as the value in-
creases.
INT/V SOL(B2)
%
SWRL CONT S/V
ON/OFF
• The control condition of the intake manifold runner
control valve (determined by ECM according to the
input signals) is indicated.
- ON: Closed
- OFF: Open
VIAS S/V-1
ON/OFF
• The control condition of the VIAS control solenoid
valve (determined by ECM according to the input
signals) is indicated.
ON: VIAS control solenoid valve is operating.
OFF: VIAS control solenoid valve is not operating.
AIR COND RLY
ON/OFF
• The air conditioner relay control condition (deter-
mined by ECM according to the input signals) is in-
dicated.
Monitored item
Unit
Description
Remarks
EC-522
< SYSTEM DESCRIPTION >
[VQ40DE FOR USA AND CANADA]
DIAGNOSIS SYSTEM (ECM)
FUEL PUMP RLY
ON/OFF
• Indicates the fuel pump relay control condition de-
termined by ECM according to the input signals.
VENT CONT/V
ON/OFF
• The control condition of the EVAP canister vent
control valve (determined by ECM according to the
input signals) is indicated.
ON: Closed
OFF: Open
THRTL RELAY
ON/OFF
• Indicates the throttle control motor relay control
condition determined by the ECM according to the
input signals.
COOLING FAN
HI/LOW/
OFF
• The control condition of the cooling fan (deter-
mined by ECM according to the input signals) is in-
dicated.
HI: High speed operation
LOW: Low speed operation
OFF: Stop
HO2S2 HTR (B1)
ON/OFF • Indicates [ON/OFF] condition of heated oxygen
sensor 2 heater determined by ECM according to
the input signals.
HO2S2 HTR (B2)
ON/OFF
I/P PULLY SPD
rpm
• Indicates the engine speed computed from the in-
put speed sensor signal.
VEHICLE SPEED
km/h or
mph
• Indicates the vehicle speed computed from the out-
put speed sensor signal.
IDL A/V LEARN
YET/
CMPLT
• Displays the condition of idle air volume learning
YET: Idle air volume learning has not been per-
formed yet.
CMPLT: Idle air volume learning has already been
performed successfully.
TRVL AFTER MIL
km or
mile
• Distance traveled while MIL is activated.
A/F S1 HTR(B1)
%
• Air fuel ratio (A/F) sensor 1 heater control value
computed by ECM according to the input signals.
• The current flow to the heater becomes larger as
the value increases.
A/F S1 HTR(B2)
%
AC PRESS SEN
V
• The signal voltage from the refrigerant pressure
sensor is displayed.
VHCL SPEED SE
km/h or
mph
• The vehicle speed computed from the vehicle
speed signal sent from TCM is displayed.
SET VHCL SPD
km/h or
mph
• The preset vehicle speed is displayed.
MAIN SW
ON/OFF
• Indicates [ON/OFF] condition from MAIN switch
signal.
CANCEL SW
ON/OFF
• Indicates [ON/OFF] condition from CANCEL switch
signal.
RESUME/ACC SW
ON/OFF
• Indicates [ON/OFF] condition from RESUME/AC-
CELERATE switch signal.
SET SW
ON/OFF
• Indicates [ON/OFF] condition from SET/COAST
switch signal.
BRAKE SW1
ON/OFF
• Indicates [ON/OFF] condition from brake pedal po-
sition switch signal.
BRAKE SW2
ON/OFF
• Indicates [ON/OFF] condition of stop lamp switch
signal.
Monitored item
Unit
Description
Remarks
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст