Nissan Frontier. Instruction — part 1332
WASHER MOTOR CIRCUIT
WW-23
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER MOTOR CIRCUIT
Diagnosis Procedure
INFOID:0000000009480069
Regarding Wiring Diagram information, refer to
.
1.
CHECK FRONT WASHER MOTOR FUSE
1. Turn the ignition switch OFF.
2. Check that the following fuse is not blown.
Is the fuse blown?
YES
>> Replace the fuse after repairing the affected circuit.
NO
>> GO TO 2
2.
CHECK WIPER AND WASHER SWITCH INPUT VOLTAGE
1. Disconnect combination switch (wiper and washer switch).
2. Turn the ignition switch ON.
3. Check voltage between combination switch (wiper and washer switch) harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK WIPER AND WASHER SWITCH GOURND CIRCUIT
Check continuity between combination switch (wiper and washer switch) harness connector and ground.
Does continuity exist?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK WIPER AND WASHER SWITCH
Check wiper and washer switch. Refer to
.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> Replace wiper and washer switch. Refer to
WW-61, "Wiper and Washer Switch"
.
5.
CHECK FRONT WASHER MOTOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Connect combination switch (wiper and washer switch).
3. Disconnect front washer motor.
4. Turn ignition switch ON.
Unit
Location
Fuse No.
Capacity
Front washer motor
Fuse block (J/B)
15
10A
Terminals
Voltage
(Approx.)
(+)
(-)
Combination switch (wiper and washer switch)
Ground
Connector
Terminal
M28
14
Battery voltage
Combination switch (wiper and washer switch)
Ground
Continuity
Connector
Terminal
M28
12
Yes
WW-24
< DTC/CIRCUIT DIAGNOSIS >
WASHER MOTOR CIRCUIT
5. Check voltage between front washer motor harness connector and ground.
Is the measurement value normal?
YES
>> Replace front washer motor. Refer to
NO
>> Repair or replace harness.
Terminal
Condition
Voltage (V)
(Approx.)
(+)
(-)
Front washer motor
Terminal
E105
1
2
Washer switch ON
Battery voltage
BCM (BODY CONTROL MODULE)
WW-25
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
ECU DIAGNOSIS INFORMATION
BCM (BODY CONTROL MODULE)
Reference Value
INFOID:0000000010218918
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Test remote keyless entry keyfob relative signal strength
VALUES ON THE DIAGNOSIS TOOL
Monitor Item
Condition
Value/Status
ACC ON SW
Ignition switch OFF or ON
Off
Ignition switch ACC
On
AIR COND SW
A/C switch OFF
Off
A/C switch ON
On
AIR PRESS FL
Front left tire air pressure value
kPa, kg/cm
2
, psi
AIR PRESS FR
Front right tire air pressure value
kPa, kg/cm
2
, psi
AIR PRESS RL
Rear left tire air pressure value
kPa, kg/cm
2
, psi
AIR PRESS RR
Rear right tire air pressure value
kPa, kg/cm
2
, psi
AUTO LIGHT SW
Lighting switch OFF
Off
Lighting switch AUTO
On
BRAKE SW
Brake pedal released
Off
Brake pedal applied
On
BUCKLE SW
Seat belt buckle unfastened
Off
Seat belt buckle fastened
On
BUZZER
Buzzer in combination meter OFF
Off
Buzzer in combination meter ON
On
CARGO LAMP SW
Cargo lamp switch OFF
Off
Cargo lamp switch ON
On
CDL LOCK SW
Door lock/unlock switch does not operate
Off
Press door lock/unlock switch to the LOCK side
On
CDL UNLOCK SW
Door lock/unlock switch does not operate
Off
Press door lock/unlock switch to the UNLOCK side
On
DOOR SW-AS
Front door RH closed
Off
Front door RH opened
On
DOOR SW-DR
Front door LH closed
Off
Front door LH opened
On
DOOR SW-RL
Rear door LH closed
Off
Rear door LH opened
On
DOOR SW-RR
Rear door RH closed
Off
Rear door RH opened
On
WW-26
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
FAN ON SIG
Blower motor fan switch OFF
Off
Blower motor fan switch ON
On
FR FOG SW
Front fog lamp switch OFF
Off
Front fog lamp switch ON
On
FR WASHER SW
Front washer switch OFF
Off
Front washer switch ON
On
FR WIPER LOW
Front wiper switch OFF
Off
Front wiper switch LO
On
FR WIPER HI
Front wiper switch OFF
Off
Front wiper switch HI
On
FR WIPER INT
Front wiper switch OFF
Off
Front wiper switch INT
On
FR WIPER STOP
Any position other than front wiper stop position
Off
Front wiper stop position
On
HAZARD SW
When hazard switch is not pressed
Off
When hazard switch is pressed
On
HEAD LAMP SW 1
Headlamp switch OFF
Off
Headlamp switch 1st
On
HEAD LAMP SW 2
Headlamp switch OFF
Off
Headlamp switch 1st
On
HI BEAM SW
High beam switch OFF
Off
High beam switch HI
On
ID REGST FL1
ID registration of front left tire incomplete
YET
ID registration of front left tire complete
DONE
ID REGST FR1
ID registration of front right tire incomplete
YET
ID registration of front right tire complete
DONE
ID REGST RL1
ID registration of rear left tire incomplete
YET
ID registration of rear left tire complete
DONE
ID REGST RR1
ID registration of rear right tire incomplete
YET
ID registration of rear right tire complete
DONE
IGN ON SW
Ignition switch OFF or ACC
Off
Ignition switch ON
On
IGN SW CAN
Ignition switch OFF or ACC
Off
Ignition switch ON
On
INT VOLUME
Wiper intermittent dial is in a dial position 1 - 7
1 - 7
KEY CYL LK-SW
Door key cylinder LOCK position
Off
Door key cylinder other than LOCK position
On
KEY CYL UN-SW
Door key cylinder UNLOCK position
Off
Door key cylinder other than UNLOCK position
On
KEY ON SW
Mechanical key is removed from key cylinder
Off
Mechanical key is inserted to key cylinder
On
KEYLESS LOCK
LOCK button of key fob is not pressed
Off
LOCK button of key fob is pressed
On
Monitor Item
Condition
Value/Status
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст