Nissan Frontier. Instruction — part 1214
REAR OIL SEAL
TM-67
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Drive the new rear oil seal (1) and new dust seal (2) using Tools.
CAUTION:
• Do not reuse rear oil seal.
• Do not incline the dust seal and rear oil seal during installa-
tion.
(A): Seal lip
For 4WD Models
• Drive the rear oil seal using Tool.
CAUTION:
• Do not reuse rear oil seal.
• Do not incline the rear oil seal during installation.
• Check the transmission oil level after installation. Refer to
.
Tool number
: ST33200000 (J-26082)
: KV38100500 ( — )
Dimension (H1)
: 1.2 - 2.2 mm (0.047 - 0.087 in)
Dimension (H2)
: 0.5 - 1.5 mm (0.020 - 0.059 in)
PCIB1660E
Tool number
: ST33200000 (J-26082)
Dimension (A)
: -0.5 - 0.5 mm (-0.020 - 0.020 in
PCIB1632E
TM-68
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
POSITION SWITCH
POSITION SWITCH
Checking
INFOID:0000000009480445
BACK-UP LAMP SWITCH
• Check continuity.
PARK/NEUTRAL POSITION SWITCH
• Check continuity.
Gear position
Continuity
Reverse
Yes
Except reverse
No
PCIB1633E
Gear position
Continuity
Neutral
Yes
Except neutral
No
SHIFT CONTROL
TM-69
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SHIFT CONTROL
Removal and Installation
INFOID:0000000009480446
COMPONENTS
REMOVAL
1. Remove the shift selector handle.
2. Remove the M/T finisher. Refer to
.
3. Remove the retaining plate and dust boot covers.
4. Remove the clip B and then separate the boot from the control housing.
5. Remove the guide plate bolts and then separate the guide plate.
6. Remove the shift selector assembly and spring from the transmission.
INSTALLATION
Installation is the reverse order of removal.
• Install shift selector handle according to the following.
1.
Retaining plate
2.
Dust boot cover (upper)
3.
Dust boot cover (lower)
4.
Shift selector handle
5.
Shift selector assembly
6.
Clip A
7.
Boot
8.
Guide plate
9.
Socket
10. Bushing
11. Clip B
12. Spring
WCIA0508E
TM-70
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
SHIFT CONTROL
- Apply cement to threads of shift selector assembly.
- Tighten shift selector handle until increased tension is felt. Then
align shift selector handle to the position as shown within one turn.
CAUTION:
Do not adjust shift selector handle by loosening it.
CAUTION:
• Apply multi-purpose grease to socket and bushing.
• Insert bushing of shift selector assembly as far as it will go into the hole of striking arm.
• Tighten guide plate (1) bolts to the specified torque in order as
shown.
•
: Front
• Do not reuse clip.
• Position clip as shown.
• Be careful with the orientation of guide plate and boot.
INSPECTION AFTER INSTALLATION
• Tighten guide plate bolts to the specified torque. Refer to
.
• When shift selector assembly is moved to each position, make sure there is no binding or disconnection in
either boot.
• When moved to each position, make sure there is no noise, bending, and backlash. Especially when shift
selector assembly is moved to 5th, 6th without pressing downward, check for bending.
• When shift selector assembly is moved to 1st, 2nd side and 5th, 6th side, confirm shift selector assembly
returns to neutral position smoothly.
• In any position other than reverse, confirm that shift selector assembly can be pressed downward.
• With shift selector assembly pressed downward, confirm that it can be moved to reverse.
• When moved from reverse to neutral position, confirm shift selector assembly returns to neutral position
smoothly with spring power.
• Without shift selector assembly pressed downward, confirm that it cannot be moved to reverse.
PCIB1435E
PCIB1668E
PCIB1434E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст