Nissan Frontier. Instruction — part 1275
TRANSMISSION ASSEMBLY
TM-311
< UNIT REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
10. Remove the starter motor.
11. Remove the front and rear propeller shafts. Refer to
DLN-134, "Removal and Installation"
143, "Removal and Installation"
DLN-174, "Removal and Installation"
.
12. Remove the left and right front exhaust tubes. Refer to
EX-6, "Removal and Installation"
.
13. Remove the shift selector control cable and bracket from the A/T.
14. Disconnect the fluid cooler tubes from the A/T assembly.
CAUTION:
Do not reuse copper sealing washers.
15. Remove the dust cover from the converter housing.
16. Turn the crankshaft to access and remove the four bolts for the
drive plate and torque converter.
CAUTION:
When turning the crankshaft, turn it clockwise as viewed
from the front of the engine.
17. Support the A/T assembly using a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to allow
it to collide against the drain plug.
18. Remove the nuts securing the insulator to the crossmember.
19. Remove the crossmember using power tool.
20. Tilt the transmission slightly to gain clearance between the body and the transmission, then disconnect
the air breather hose.
21. Disconnect the following:
• A/T assembly harness connector
• 4LO switch harness connector
• Wait detection switch harness connector
• ATP switch harness connector
• Transfer control device harness connector
22. Remove the wiring harness from the retainers.
23. Remove the A/T fluid indicator pipe.
24. Remove the A/T assembly to engine bolts using power tool.
25. Remove A/T assembly with transfer from the vehicle using Tool.
CAUTION:
• Secure the torque converter to prevent it from dropping.
• Secure the A/T assembly to a transmission jack.
NOTE:
The actual special service Tool may differ from Tool shown.
26. Remove the transfer from the A/T assembly. Refer to
INSPECTION
Installation and Inspection of Torque Converter
• After inserting a torque converter to a transmission, be sure to
check dimension (A) to ensure it is within the reference value limit.
Tool number
:
—
(J-47002)
LCIA0335E
SCIA2203E
Dimension (A)
: 25.0 mm (0.98 in) or more
SAT017B
TM-312
< UNIT REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
INSTALLATION
Installation of the remaining components is in the reverse order of removal, while paying attention to the fol-
lowing.
• When installing transmission to the engine, tighten the bolts to the
specified torque using sequence shown.
• Align the positions of bolts for drive plate with those of the torque
converter, and temporarily tighten the bolts. Then, tighten the bolts
with the specified torque.
CAUTION:
• When turning crankshaft, turn it clockwise as viewed from the
front of the engine.
• After converter is installed to drive plate, rotate crankshaft
several turns and check to be sure that transmission rotates
freely without binding.
• When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.
• Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drive train components.
• Install crankshaft position sensor (POS).
• After completing installation, check fluid leakage, fluid level, and the positions of A/T. Refer to
"Checking the A/T Fluid (ATF)"
,
TM-285, "Inspection and Adjustment"
.
Transmission bolts
: 75 N·m (7.6 kg-m, 55 ft-lb)
LCIA0370E
LCIA0335E
OVERHAUL
TM-313
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
OVERHAUL
Exploded View
INFOID:0000000009480692
SCIA7040E
TM-314
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
OVERHAUL
1.
O-ring
2.
Oil pump cover
3.
O-ring
4.
Oil pump housing
5.
Self-sealing bolt
6.
Torque converter
7.
Converter housing
8.
Oil pump housing oil seal
9.
Bearing race
10. Needle bearing
11. O-ring
12. Front carrier assembly
13. Needle bearing
14. Snap ring
15. Front sun gear
16. 3rd one-way clutch
17. Snap ring
18. Bearing race
19. Needle bearing
20. Seal ring
21. Input clutch assembly
22. Needle bearing
23. Rear internal gear
24. Brake band
25. Mid carrier assembly
26. Needle bearing
27. Bearing race
28. Rear carrier assembly
29. Needle bearing
30. Mid sun gear
31. Seal ring
32. Rear sun gear
33. 1st one-way clutch
34. Snap ring
35. Needle bearing
36. High and low reverse clutch hub
37. Snap ring
38. Bearing race
39. Needle bearing
: Apply Genuine RTV silicone sealant or equivalent. Refer to
GI-21, "Recommended Chemical Products and Sealants"
Refer to
for symbols not described on the above.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст