Nissan Frontier. Instruction — part 1132
P1610 LOCK MODE
SEC-25
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
P1610 LOCK MODE
Description
INFOID:0000000009479050
When the starting operation is carried more than five times consecutively under the following conditions, NATS
will shift to the mode which prevents the engine from being started.
• Unregistered mechanical key is used.
• BCM or ECM's malfunctioning.
DTC Logic
INFOID:0000000009479051
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009479052
1.
CHECK ENGINE START FUNCTION
1. Perform the check for DTC except DTC P1610.
2. Use CONSULT to erase DTC after fixing.
3. Check that engine can start with registered mechanical key.
Does the engine start?
YES
>> Inspection End.
NO
>> GO TO 2
2.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> Inspection End.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P1610
LOCK MODE
When the starting operation is carried out
five or more times consecutively under the
following conditions.
• Unregistered mechanical key
• BCM or ECM's malfunctioning.
—
SEC-26
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
BCM
BCM : Diagnosis Procedure
INFOID:0000000010214655
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
Is the fuse blown?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit.
NO
>> GO TO 2
2.
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Terminal No.
Signal name
Fuses and fusible link No.
57
Battery power supply
21 (10A)
70
G (50A)
11
Ignition ACC or ON
4 (10A)
38
Ignition ON or START
1 (10A)
Connector
Terminals
Power
source
Condition
Voltage (V) (Ap-
prox.)
(+)
(-)
M18
11
Ground
ACC
power
supply
Ignition
switch
ACC or
ON
Battery voltage
38
Ground
Ignition
power
supply
Ignition
switch ON
or START
Battery voltage
M20
57
Ground
Battery
power
supply
Ignition
switch
OFF
Battery voltage
70
Ground
Battery
power
supply
Ignition
switch
OFF
Battery voltage
LIIA2415E
POWER SUPPLY AND GROUND CIRCUIT
SEC-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Inspection End.
NO
>> Repair or replace harness.
BCM
Ground
Continuity
Connector
Terminal
M20
67
Yes
LIIA0915E
SEC-28
< DTC/CIRCUIT DIAGNOSIS >
KEY CYLINDER SWITCH
KEY CYLINDER SWITCH
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000009479054
The main power window and door lock/unlock switch detects condition of the door key cylinder switch and
transmits to BCM as the LOCK or UNLOCK signal.
DRIVER SIDE : Component Function Check
INFOID:0000000009479055
1.
CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
Check "KEY CYL LK-SW" AND "KEY CYL UN-SW" in DATA MONITOR mode for “POWER DOOR LOCK
SYSTEM” with CONSULT.
Is the inspection result normal?
YES
>> Key cylinder switch is OK.
NO
>> Refer to
SEC-28, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000009479056
Regarding Wiring Diagram information, refer to
SEC-52, "Wiring Diagram - King Cab"
.
1.
CHECK DOOR KEY CYLINDER SWITCH LH
With CONSULT
Check front door lock assembly LH (key cylinder switch) ("KEY CYL LK-SW") and ("KEY CYL UN-SW) in
DATA MONITOR mode in CONSULT. Refer to
BCS-15, "DOOR LOCK : CONSULT Function (BCM - DOOR
• When key inserted in front key cylinder is turned to LOCK:
• When key inserted in front key cylinder is turned to UNLOCK:
Without CONSULT
1. Turn ignition switch OFF.
2. Check voltage between BCM connector M18 terminals 7, 8 and
ground.
Monitor item
Condition
KEY CYL LK-SW
Lock
: ON
Neutral / Unlock
: OFF
KEY CYL UN-SW
Unlock
: ON
Neutral / Lock
: OFF
KEY CYL LK-SW
: ON
KEY CYL UN-SW
: ON
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
WIIA0457E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст