Nissan Frontier. Instruction — part 271
DLK-130
< REMOVAL AND INSTALLATION >
HOOD
Installation is in the reverse order of removal.
Removal and Installation of Hood Lock Control
INFOID:0000000009478954
REMOVAL
1. Disconnect the hood lock cable from the hood lock, and unclip it from the radiator core support upper and
hoodledge.
2. Remove the bolts, and the hood release handle.
3. Separate the grommet from the lower dash panel. Pull the hood lock cable out through the passenger
compartment.
CAUTION:
While pulling, be careful not to damage the outside of the hood lock cable.
INSTALLATION
1. Pull the hood lock cable through the lower dash panel hole into the engine room.
CAUTION:
1.
Hood lock assembly
2.
Hood lock cable
WIIA0775E
HOOD
DLK-131
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Be careful not to bend the cable too much, keep the radius
100mm (3.94 in) or more.
2. Make sure the cable is not offset from the grommet, and push
the grommet into the lower dash panel hole securely.
3. Apply sealant around the grommet at * mark.
4. Install the cable securely to the lock.
5. Adjust the hood lock. Refer to
Hood Lock Control Inspection
INFOID:0000000009478955
1. Make sure the hood lock cable is not bent or deformed. If the cable is damaged, replace it.
2. Remove the front grille. Refer to
.
3. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height.
4. While operating the hood opener, carefully make sure the front
end of the hood is raised by approx. 20 mm (0.79 in). Also make
sure the hood opener returns to the original position.
5. Check the hood lock lubrication condition. If necessary, apply
“body grease” to the points shown.
6. Install the front grille. Refer to
LIIA1698E
LIIA1699E
PIIA1086E
PIIA0176E
DLK-132
< REMOVAL AND INSTALLATION >
DOOR
DOOR
Fitting Adjustment
INFOID:0000000009478956
KING CAB
AWKIA0544ZZ
D.
4.5 mm
± 1.0 mm (0.177 in ± 0.039 in)
DOOR
DLK-133
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CREW CAB
FRONT DOOR
Longitudinal clearance and surface height adjustment at front end
1. Remove the front fender. Refer to
EXT-25, "Removal and Installation"
.
2. Loosen the hinge bolts. Raise the front door at rear end to adjust.
3. Install the front fender. Refer to
EXT-25, "Removal and Installation"
REAR DOOR
Longitudinal clearance and surface height adjustment at front end
1. Remove the center pillar upper finisher. Refer to
2. Accessing from inside the vehicle, loosen the nuts. Open the rear door, and raise the rear door at rear end
to adjust.
3. Install the center pillar lower finisher. Refer to
.
STRIKER ADJUSTMENT
1. Adjust the striker so that it becomes parallel with the lock inser-
tion direction.
AWKIA0545ZZ
D.
4.5 mm
± 1.0 mm (0.177 in ± 0.039 in)
Striker bolts
: 16.7 N·m (1.7 kg–m, 12 ft–lb)
LIIA1621E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст