Nissan Frontier. Instruction — part 711
OIL PAN
EM-33
< REMOVAL AND INSTALLATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
OIL PAN
Exploded View
INFOID:0000000009478055
Removal and Installation
INFOID:0000000009478056
REMOVAL
WARNING:
To avoid the danger of being scalded, do not drain engine oil when engine is hot.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove engine under cover. Refer to
EXT-15, "Removal and Installation"
.
2. Drain engine oil. Refer to
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine oil on drive belt.
3. Remove 3rd crossmember assembly.
4. Remove lower joint shaft pinch bolt at steering gear. Refer to
ST-12, "Removal and Installation"
.
5. Remove steering gear bolts. Refer to
ST-15, "Removal and Installation"
.
6. Remove oil pan with the following procedure:
a. Loosen bolts in reverse order as shown with power tool.
Remove A/T fluid cooler tube bracket (A/T models).
1.
Oil pan
2.
A/T fluid cooler tube bracket (A/T models)
3.
Drain plug
4.
Drain plug washer
PBIC2992E
PBIC2993E
EM-34
< REMOVAL AND INSTALLATION >
[QR25DE]
OIL PAN
b. Insert Tool between the oil pan and the cylinder block and
remove oil pan.
CAUTION:
• Be careful not to damage the mating surfaces.
• Do not insert a screwdriver, this will damage the mating
surfaces.
NOTE:
Tap (1) Tool to insert it and then slide (2) it by tapping on the side
of the Tool as shown.
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSTALLATION
1. Install oil pan with the following procedure:
a. Use a scraper to remove old liquid gasket from mating surfaces.
• Also remove the old liquid gasket from mating surface of cylin-
der block.
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
b. Apply a continuous bead of liquid gasket using Tool as shown.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-21, "Recommended Chemical Products and Sealants"
.
CAUTION:
Attaching should be done within 5 minutes after coating.
c.
Tighten bolts in numerical order as shown.
• Install A/T fluid cooler tube bracket with bolts No.1 and 9 as
shown (A/T models).
2. Install oil pan drain plug. Refer to
.
3. Installation is in the reverse order of removal after this step.
NOTE:
Pour engine oil at least 30 minutes after oil pan is installed.
Tool number
: KV10111100 (J-37228)
WBIA0566E
PBIC2994E
Tool number
: WS39930000 (
—
)
PBIC2984E
PBIC2993E
OIL PAN
EM-35
< REMOVAL AND INSTALLATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
INSPECTION AFTER INSTALLATION
• Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-16, "FOR USA AND CANADA : Fluids and Lubricants"
(United
States and Canada).
• Use procedure below to check for fuel leakage.
• Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leak-
age at connection points.
• Start engine. With engine speed increased, check again for fuel leakage at connection points.
• Run engine to check for unusual noise and vibration.
NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal and installation, slack in the guide
may generate a pounding noise during and just after engine start. However, this is normal. Noise will stop
after hydraulic pressure rises.
• Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gas, or any oils/fluids including
engine oil and engine coolant.
• Bleed air from passages in lines and hoses, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to spec-
ified level, if necessary.
• Summary of the inspection items:
*Power steering fluid, brake fluid, etc.
Item
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Transmission/
transaxle fluid
A/T and CVT Models
Leakage
Level/Leakage
Leakage
M/T Models
Level/Leakage
Leakage
Level/Leakage
Other oils and fluids*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gas
—
Leakage
—
EM-36
< REMOVAL AND INSTALLATION >
[QR25DE]
IGNITION COIL
IGNITION COIL
Exploded View
INFOID:0000000009478057
Removal and Installation
INFOID:0000000009478058
REMOVAL
1. Remove intake manifold. Refer to
.
2. Disconnect harness connector from ignition coil.
3. Remove ignition coil.
CAUTION:
Do not shock ignition coil.
INSTALLATION
Installation is in the reverse order of removal.
1.
Ignition coil
2.
Spark plug
3.
Rocker cover
WBIA0648E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст