Nissan Frontier. Instruction — part 848
PREPARATION
GW-9
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000010129253
The actual shape of tools may differ from those illustrated here.
Commercial Service Tool
INFOID:0000000010129254
Tool number
(TechMate No.)
Tool name
Description
—
(J-39570)
Chassis Ear
Locating the noise
—
(J-50397)
NISSAN Squeak and Rattle Kit
Repairing the cause of noise
SIIA0993E
ALJIA1232ZZ
(TechMate No.)
Tool name
Description
(J-39565)
Engine Ear
Locating the noise
(
—
)
Suction lifter
Holding the door glass
SIIA0995E
PIIB1805J
GW-10
< REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
REMOVAL AND INSTALLATION
WINDSHIELD GLASS
Removal and Installation
INFOID:0000000009478973
REMOVAL
1. Remove inside mirror. Refer to
MIR-22, "Inside Mirror Assembly"
.
2. Remove the front pillar upper finisher. Refer to
INT-19, "Removal and Installation"
.
3. Remove cowl top cover. Refer to
EXT-24, "Removal and Installation"
.
4. Remove windshield glass using piano wire or power cutting tool (A) and an inflatable pump bag (B).
• Apply protective tape around the windshield glass to protect the painted surface from damage.
• If the windshield glass is to be reused, mark the body and the glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
• Be careful not to scratch the glass when removing.
• Do not set or stand glass on its edge. Small chips may develop into cracks.
• Protect the painted surface around the windshield glass from damage.
INSTALLATION
Installation is in the reverse order of removal.
• Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger compartment air pressure when a door is closed.
1.
Molding
2.
Windshield
3.
Windshield position pins
4.
Mirror base
5.
Insulator
LIIA1684E
PIIB5779E
WINDSHIELD GLASS
GW-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
• The molding must be installed securely so that it is in position and leaves no gap.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the windshield in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidities. The curing time will increase
under lower temperatures and lower humidities.
GW-12
< REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
1.
Windshield glass
2.
Molding
3.
Roof
4.
Urethane
5.
A-pillar
6.
Primer
7.
Cowl top panel
8.
Insulator
9.
Instrument panel
10. Cowl top cover
A.
Primer area (top and sides)
B.
Primer area (bottom)
C.
Bond area (top and sides)
D.
Bond area (bottom)
a.
7.0 mm (0.28 in)
WIIA1032E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст