Nissan Frontier. Instruction — part 176
BRC-232
< PRECAUTION >
[TYPE 2]
PRECAUTIONS
• Area to be repaired must be soldered and wrapped with tape.
Make sure that fraying of twisted wire is within 110 mm (4.33 in).
• Do not make a bypass connection to repaired area. (If the circuit is
bypassed, characteristics of twisted wire will be lost.)
PKIA0306E
PKIA0307E
PREPARATION
BRC-233
< PREPARATION >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009479553
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tool
INFOID:0000000009479554
Tool number
(TechMate No.)
Tool name
Description
KV991J0080
(J-45741)
ABS active wheel sensor tester
Checking operation of ABS active wheel sen-
sors
ST30031000
(
—
)
Bearing puller
Removing sensor rotor
WFIA0101E
ZZA0700D
Tool name
Description
1. Flare nut crowfoot
2. Torque wrench
Removing and installing brake piping
a: 10 mm (0.39 in)/12 mm (0.47 in)
Power tool
Loosening nuts, screws and bolts
S-NT360
PIIB1407E
BRC-234
< UNIT REMOVAL AND INSTALLATION >
[TYPE 2]
WHEEL SENSOR
UNIT REMOVAL AND INSTALLATION
WHEEL SENSOR
Removal and Installation
INFOID:0000000009479555
REMOVAL
1. Remove wheel sensor bolt.
• When removing the front wheel sensor, first remove the disc rotor to gain access to the front wheel sen-
sor. Refer to
BR-35, "Removal and Installation of Brake Caliper and Disc Rotor"
2. Pull the wheel sensor straight out, being careful to turn it as little as possible.
CAUTION:
• Be careful not to damage the wheel sensor edge and sensor rotor teeth.
• Do not pull on the wheel sensor harness.
3. Disconnect wheel sensor harness connector, then remove the wheel sensor harness from the mounts to
remove the wheel sensor.
INSTALLATION
Installation is in the reverse order of removal.
• Before installing wheel sensors do the following:
- Inspect and replace the wheel sensor if damaged.
- Clean the wheel sensor hole and mating surface with brake cleaner and a lint-free cloth. Be careful that dirt
and debris do not enter the hub and bearing assembly or the rear axle.
1.
Front wheel sensor
2.
Rear wheel sensor (C200)
3.
Rear wheel sensor (M226)
WFIA0339E
SENSOR ROTOR
BRC-235
< UNIT REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SENSOR ROTOR
Removal and Installation
INFOID:0000000009479556
FRONT
Removal and Installation
The wheel sensor rotors are built into the wheel hubs and are not removable. If damaged, replace wheel hub
and bearing assembly. Refer to
FAX-8, "Removal and Installation"
REAR (C200)
Removal and Installation
It is necessary to disassemble the rear axle to replace the sensor rotor. Perform the axle shaft assembly
removal procedure to replace sensor rotor. Refer to
RAX-7, "Removal and Installation"
.
REAR (M226)
Removal
1. Remove the axle shaft assembly. Refer to
RAX-19, "Removal and Installation"
2. Pull the sensor rotor off of the axle shaft using Tool and a suitable press.
Installation
1. Install the new sensor rotor on the axle shaft using a suitable
length steel tube and a press. Make sure the sensor rotor is fully
seated.
CAUTION:
Do not reuse the old sensor rotor.
2. Install the axle shaft assembly. Refer to
.
CAUTION:
Do not reuse the axle oil seal. The axle oil seal must be
replaced every time the axle shaft assembly is removed
from the axle shaft housing.
Tool number
: ST30031000 (
—
)
WFIA0341E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст