Nissan Frontier. Instruction — part 733
PRECAUTIONS
EM-121
< PRECAUTION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
3. Attach the liquid gasket tube to the Tool.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-21, "Recommended Chemical Products and Sealants"
.
4. Apply the liquid gasket without breaks to the specified location
with the specified dimensions.
• If there is a groove for the liquid gasket application, apply the
liquid gasket to the groove.
• Normally apply the liquid gasket on the inside edge of the bolt
holes. Also apply to the outside edge of the bolt holes when
specified in the procedure.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten after the installation.
• Wait 30 minutes or more after installation before refilling the
engine with oil or coolant.
CAUTION:
If there are more specific instructions in the procedures contained in this instruction conerning liquid
gasket application, observe them.
Tool number
: WS39930000 ( — )
WBIA0567E
SEM159F
EM-122
< PREPARATION >
[VQ40DE]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009478091
The actual shape of the tools may differ from those tools illustrated here.
Tool number
(TechMate No.)
Tool name
Description
ST0501S000
( — )
Engine stand assembly
1. ST05011000
( — )
Engine stand
2. ST05012000
( — )
Base
Disassembling and assembling engine
16441 6N210
(J-45488)
Quick connector release
Removing fuel tube quick connectors in en-
gine room.
KV10111100
(J-37228)
Seal cutter
Removing oil pan (lower and upper), front and
rear timing chain case, etc.
WS39930000
( — )
Tube presser
Pressing the tube of liquid gasket
KV991J0050
(J-44626)
Air fuel sensor Socket
Loosening or tightening air fuel ratio A/F sen-
sor
a: 22 mm (0.87 in)
KV10114400
(J-38365)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sor 1
a: 22 mm (0.87 in)
NT042
PBIC0198E
NT046
NT052
LBIA0444E
NT636
PREPARATION
EM-123
< PREPARATION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
KV10116200
(J-26336-B)
Valve spring compressor
1. KV10115900
(J-26336-20)
Attachment
2.KV10109220
( — )
Adapter
Disassembling valve mechanism
Part (1) is a component of KV10116200 (J-
26336-B), but Part (2) is not so.
KV10107902
(J-38959)
Valve oil seal puller
Replacing valve oil seal
—
(J-39386)
Valve oil seal drift
Installing valve oil seal
EM0347000
(J-8037)
Piston ring compressor
Installing piston assembly into cylinder bore
KV10112100
(BT-8653-A)
Angle wrench
Tightening bolts for cylinder head, main bear-
ing cap and connecting rod cap
ST16610001
(J-23907)
Pilot bushing puller
Removing pilot converter
—
1. (J-49815)
2. (J-8092)
Seal installer and driver handle
Installing rear main seal
Tool number
(TechMate No.)
Tool name
Description
PBIC1650E
NT011
NT024
NT044
AWBIA1043ZZ
NT045
AWBIA0862ZZ
EM-124
< PREPARATION >
[VQ40DE]
PREPARATION
Commercial Service Tool
INFOID:0000000009478092
KV11105210
(J-44716)
Ring gear stopper
Removing and installing crankshaft pulley
—
(J-50246)
Tensioner shoe installer and chain ten-
sioner pins
Installing secondary timing chain tensioner
shoes and locking chain tensioners in com-
pressed position
Tool number
(TechMate No.)
Tool name
Description
ALBIA0523ZZ
ALBIA0678ZZ
Tool number
(TechMate No.)
Tool name
Description
1. Crowfoot
2. Torque wrench
Installing exhaust manifold nuts
a: 14 mm (0.55 in)
Power tool
Loosening nuts, screws and bolts
KV991J0100
(J-46531)
Socket
Removing and installing flywheel
Size: T55
( — )
Spark plug wrench
Removing and installing spark plug
S-NT360
PIIB1407E
PBIC1113E
NT047
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст