Nissan Frontier. Instruction — part 1121

FRONT SEAT

SE-29

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

Instruction Driver Seat

AWJIA0467GB

1.

Headrest

2.

Seatback assembly

3.

Lumbar support lever knob

4.

Snap ring

5.

Seat cushion trim cover

6.

Seat cushion pad

7.

Seat cushion frame

8.

Seat cushion inner finisher

9.

Seat belt buckle assembly

10. Seat frame assembly

11. Leg cover

12. Bolt cover

13. Recline lever

14. Seat cushion outer finisher

15. Leg cover

SE-30

< REMOVAL AND INSTALLATION >

FRONT SEAT

Conventional Passenger Seat

16. Seat cushion rear finisher

17. Seat cushion lift knobs

18. Seatback board

19. Headrest holder with multi position

lock

20. Headrest holder

AWJIA0468GB

1.

Headrest

2.

Seatback assembly with side air bag 3.

Switch assembly

4.

Power seat switch escutcheon

5.

Recliner switch knob

6.

Slide switch knob

7.

Seat cushion assembly

8.

Seat cushion outer cover

9.

Leg cover

FRONT SEAT

SE-31

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

Fold Flat Passenger Seat

10. Seat cushion front finisher

11. Passenger seat wiring harness

12. Power seat frame assembly

13. Seat cushion inner finisher

14. Seat belt buckle assembly

15. Leg cover

16. Seat cushion rear finisher

17. Instruction seat frame assembly

18. Recline lever

19. Seat cushion rear finisher

20. Seatback board

21. Headrest holder with multi position

lock

22. Headrest holder

AWJIA0469GB

SE-32

< REMOVAL AND INSTALLATION >

FRONT SEAT

Removal and Installation

INFOID:0000000009479574

REMOVAL

CAUTION:

• Before removing the front seat, turn the ignition switch off, disconnect both battery terminals and

wait at least three minutes.

• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-

tor with the side air bag module connector. Such an error may cause the air bag to deploy.

• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with

care.

• After front side air bag module inflates, front seatback assembly must be replaced.

• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-

ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect

the Occupant Classification System calibration.

• Always replace passenger seat cushion as an assembly.

• When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
1. Slide the seat until the four bolts are visible and a suitable tool can be inserted.

NOTE:

Set the front/rear cushion lifters to the top position.

2. Disconnect both battery terminals and wait at least three minutes. Refer to

PG-83, "Removal and Installa-

tion"

.

3. Disconnect the harness connector from the side air bag module.
4. Remove the leg covers.
5. Remove the four front seat bolts.
6. Disconnect the harness connectors from the power seat and remove.

NOTE:

When removing and installing the seat, use shop cloths to protect the vehicle from damage.

INSTALLATION

Installation is in the reverse order of removal.

1.

Front seatback lever

2.

Headrest

3.

Seatback assembly

4.

Seat cushion assembly

5.

Seat cushion outer finisher

6.

Leg cover

7.

Seat frame assembly

8.

Passenger seat wiring harness

9.

Seat cushion inner cover

10. Inboard reclining arm outer cover

11. Seat belt buckle assembly

12. Leg cover

13. Inboard reclining arm inner cover

14. Outboard reclining arm inner cover

15. Seat cushion rear finisher

16. Outboard reclining arm outer cover

17. Seatback board

18. Headrest holder with multi position

lock

19. Headrest holder