Nissan Frontier. Instruction — part 1155
SR-10
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009480297
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
—
(J-42057-UPD)
Air bag key set
Part of kit (J-42057)
Removing and installing air bag lock
LRS210
DRIVER AIR BAG MODULE
SR-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
REMOVAL AND INSTALLATION
DRIVER AIR BAG MODULE
Removal and Installation
INFOID:0000000009480298
REMOVAL
CAUTION:
• Do not attempt to repair or replace damaged direct-connect SRS component connectors. If a driver
air bag direct-connect harness connector is damaged, the spiral cable must be replaced.
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals and wait at
least three minutes.
• When servicing the SRS, do not work from directly in front of air bag module.
1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to
2. Locate retaining clip access hole and insert suitable 4mm - 6mm blunt tool.
NOTE:
Do not use sharp edged objects such as screwdrivers to release driver air bag module from steering
wheel, SRS components may be unintentionally damaged.
1.
Steering wheel
2.
Retaining clip
3.
Driver air bag module connectors
4.
Driver air bag module
5.
Retaining clip access hole
6.
Horn connector
LHIA0084E
LHIA0085E
SR-12
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
3. Press upward (toward center of steering wheel) on retaining clip until driver air bag module is released
from steering wheel.
4. Lift the driver air bag module from the steering wheel.
5. Disconnect the driver air bag module and horn connectors, then remove the driver air bag module.
• For removal/installation of the direct-connect SRS connectors, refer to
.
CAUTION:
• When servicing the SRS, do not work from directly in front of air bag module.
• Always place air bag module with pad side facing
upward.
• Do not insert any foreign objects (screwdriver, etc.) into
air bag module or connectors.
• Do not disassemble air bag module.
• Do not expose the air bag module to temperatures
exceeding 90
°C (194°F).
• Replace the air bag module if it has been dropped or
sustained an impact.
• Do not allow oil, grease or water to come in contact with
the air bag module.
INSTALLATION
Installation is in the reverse order of removal.
• If driver air bag module is being replaced due to deployment, spiral cable must also be replaced. Refer to
SR-13, "Removal and Installation"
.
• For removal/installation of the direct-connect SRS connectors, refer to
SRC-9, "Direct-connect SRS Compo-
• After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
LHIA0086E
SBF814E
SPIRAL CABLE
SR-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SPIRAL CABLE
Removal and Installation
INFOID:0000000009480299
REMOVAL
CAUTION:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals and wait at
least three minutes.
• When servicing the SRS, do not work from directly in front of air bag module.
1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to
2. Set the front wheels in the straight-ahead position.
3. Remove the steering wheel. Refer to
ST-11, "Removal and Installation"
.
4. Remove the steering column upper and lower covers. Refer to
IP-16, "Removal and Installation"
.
5. Disconnect wiper and washer switch connector. Then while
pressing tabs, pull wiper and washer switch away from spiral
cable to remove.
LHIA0087E
1.
Steering wheel
2.
Lighting and turn signal switch
3.
Spiral cable
4.
Steering column upper cover
5.
Steering column assembly
6.
Screw
7.
Steering column lower cover
8.
Wiper and washer switch
9.
Driver air bag module connectors
LHIA0034E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст