Nissan Frontier. Instruction — part 719
OIL SEAL
EM-65
< REMOVAL AND INSTALLATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Press-fit front oil seal until it is flush with front end surface of
front cover using suitable tool.
CAUTION:
• Be careful not to damage front cover and crankshaft.
• Press-fit straight and avoid causing burrs or tilting oil
seal.
3. Tighten crankshaft pulley bolt.
• Secure crankshaft pulley using suitable tool, and tighten crankshaft pulley bolt.
a. Apply new engine oil to thread and seat surfaces of crankshaft pulley bolt.
b. Tighten crankshaft pulley bolt.
c. Put a paint mark on crankshaft pulley, mating with any one of six
easy to recognize angle marks on bolt flange.
d. Turn another 60
° degrees clockwise (angle tightening).
• Check the tightening angle with movement of one angle mark.
4. Installation is in the reverse order of removal after this step.
Removal and Installation of Rear Oil Seal
INFOID:0000000009478070
REMOVAL
1. Remove transmission assembly. Refer to
TM-21, "Removal and Installation from Vehicle"
TM-306, "Removal and Installation for QR25DE"
2. Remove clutch cover and clutch disk (M/T models). Refer to
CL-19, "5M/T : Removal and Installation"
3. Remove drive plate (A/T models) or flywheel (M/T models) with power tool. Refer to
.
4. Remove rear oil seal with a suitable tool.
CAUTION:
Be careful not to damage crankshaft and cylinder block.
INSTALLATION
1. Apply new engine oil to new rear oil seal joint surface and seal lip.
2. Install rear oil seal so that each seal lip is oriented as shown.
PBIC3033E
Crankshaft pulley bolt
: 42.1 N·m (4.3 kg-m, 31 ft-lb)
SEM751G
SEM715A
EM-66
< REMOVAL AND INSTALLATION >
[QR25DE]
OIL SEAL
• Install new rear oil seal using suitable tool. [outside diameter
102 mm (4.02 in), inside diameter 86 mm (3.39 in)].
CAUTION:
• Be careful not to damage crankshaft and cylinder block.
• Press-fit oil seal straight to avoid causing burrs or tilt-
ing.
• Do not touch grease applied onto oil seal lip.
• Press in rear oil seal to the position as shown.
3. Installation of the remaining components is in the reverse order of removal.
CAUTION:
• When replacing an engine or transmission you must make sure the dowels are installed cor-
rectly during reassembly.
• Improper alignment caused by missing dowels may cause vibration, oil leaks or breakage of
drivetrain components.
SBIA0280E
WBIA0654E
CYLINDER HEAD
EM-67
< REMOVAL AND INSTALLATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CYLINDER HEAD
Exploded View
INFOID:0000000009478071
Removal and Installation
INFOID:0000000009478072
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Release fuel pressure. Refer to
.
2. Drain engine coolant. Refer to
CO-12, "Changing Engine Coolant"
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine coolant on drive belt.
3. Drain engine oil. Refer to
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine oil on drive belt.
4. Remove intake manifold. Refer to
.
5. Remove fuel injector and fuel tube assembly. Refer to
6. Remove exhaust manifold and three way catalyst assembly. Refer to
.
7. Remove water outlet. Refer to
CO-28, "Removal and Installation"
8. Remove heater outlet. Refer to
NOTE:
Can be removed and installed even when assembled with cylinder head.
9. Remove front cover and timing chain. Refer to
10. Remove camshafts. Refer to
.
1.
Cylinder head assembly
2.
Cylinder head gasket
3.
Cylinder head bolt
EM-67, "Removal and Installation"
WBIA0835E
EM-68
< REMOVAL AND INSTALLATION >
[QR25DE]
CYLINDER HEAD
11. Loosen cylinder head bolts in reverse order as shown using
power tool.
12. Remove cylinder head.
13. Remove cylinder head gasket.
INSPECTION AFTER REMOVAL
Cylinder Head Bolts Outer Diameter
• Cylinder head bolts are tightened by plastic zone tightening
method. Whenever the size difference between (d1) and (d2)
exceeds the limit, replace them with a new one.
• If reduction of outer diameter appears in a position other than (d2),
use it as (d2) point.
Cylinder Head Distortion
NOTE:
When performing this inspection, cylinder block distortion should also be checked. Refer to
.
1. Using suitable tool, wipe off oil, scale, gasket, sealant and carbon deposits from surface of cylinder head.
CAUTION:
Do not allow gasket fragments to enter engine oil or engine coolant passages.
2. At each of several locations on bottom surface of cylinder head,
measure the distortion in six directions.
• If it exceeds the limit, replace cylinder head.
INSTALLATION
1. Install new cylinder head gasket.
2. Install cylinder head following the steps below to tighten cylinder
head bolts in numerical order as shown.
CAUTION:
If cylinder head bolts re-used, check their outer diameters
before installation. Follow the "Cylinder Head Bolts Outer
Diameter" procedure.
NOTE:
Apply new engine oil to threads and seating surfaces of bolts.
KBIA0058E
Limit [(d1) (d2)]: 0.23 mm (0.0091 in)
WBIA0836E
Limit
: 0.1 mm (0.004 in)
PBIC0075E
KBIA0058E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст