Nissan Frontier. Instruction — part 1188
SERVICE DATA AND SPECIFICATIONS (SDS)
ST-31
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Tie-rod
INFOID:0000000009479933
Oil Pump
INFOID:0000000009479934
Steering Fluid
INFOID:0000000009479935
Outer socket
Swinging torque
0.3
− 2.9 N·m (0.03 − 0.29 kg-m, 3 − 25 in-lb)
Measurement on spring balance
• Measuring point: cotter pin hole of stud
4.84
− 46.7 N (0.50 − 4.7 kg-f, 4 − 34 lb-f)
Rotating torque
0.3
− 2.9 N·m (0.03 − 0.29 kg-m, 3 − 25 in-lb)
Axial end play
0.5 mm (0.020 in) or less
Inner socket
Swinging torque
1.0
− 7.8 N·m (0.11 − 0.79 kg-m, 9 − 69 in-lb)
Measurement on spring balance
• Measuring point: L mark see above,
L=83.2 mm (3.276 in).
12.1
− 93.7 N (1.3 − 9.5 kg-f, 9 − 69 lb-f)
Axial end play
0.2 mm (0.08 in) or less
Rack sliding force
Standard
280
± 30 N (28.6 ± 3.1 kg-f, 62.9 ± 6.7 lb-f)
Minimum
210 N (21.4 kg-f, 47.2 lb-f)
Steering gear type
PR26AM
Tie-rod maximum length (L)
84 mm (3.31 in)
SGIA0167E
Oil pump relief hydraulic pressure - Maximum
8.8 mPa (89.76 kg/cm
2
, 1276 psi)
Fluid capacity
Approx. 1.0 (2 1/8 US pt, 1 3/4 Imp pt)
STR-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
STR
A
STR
N
O
P
CONTENTS
STARTING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Power Generation Variable Voltage
Control System . . . . . . . . . . . . . . ..
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
Work Flow (With GR8-1200 NI) . . . . . . . ....
Work Flow (Without GR8-1200 NI) . . . . . . .
SYSTEM DESCRIPTION . . . . . . . .
STARTING SYSTEM . . . . . . . . . . ..
A/T . . . . . . . . . . . . . . . . . . . .
A/T : System Diagram . . . . . . . . . . . .
A/T : System Description . . . . . . . . . . .
A/T : Component Parts Location . . . . . . . .
A/T : Component Description . . . . . . . . ..
M/T WITH CLUTCH INTERLOCK CANCEL SYS-
TEM . . . . . . . . . . . . . . . . . . .
M/T WITH CLUTCH INTERLOCK CANCEL SYS-
TEM : System Diagram . . . . . . . . . . ...
M/T WITH CLUTCH INTERLOCK CANCEL SYS-
TEM : System Description . . . . . . . . . ...
M/T WITH CLUTCH INTERLOCK CANCEL SYS-
TEM : Component Parts Location . . . . . . ...
M/T WITH CLUTCH INTERLOCK CANCEL SYS-
TEM : Component Description . . . . . . . .
M/T WITHOUT CLUTCH INTERLOCK CANCEL
SYSTEM . . . . . . . . . . . . . . . . . .
M/T WITHOUT CLUTCH INTERLOCK CANCEL
SYSTEM : System Diagram . . . . . . . . .
M/T WITHOUT CLUTCH INTERLOCK CANCEL
SYSTEM : System Description . . . . . . . .
M/T WITHOUT CLUTCH INTERLOCK CANCEL
SYSTEM : Component Parts Location . . . . .
M/T WITHOUT CLUTCH INTERLOCK CANCEL
SYSTEM : Component Description . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
B TERMINAL CIRCUIT . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
S CONNECTOR CIRCUIT . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ..
STARTING SYSTEM . . . . . . . . . . .
Wiring Diagram - VQ40DE With Clutch Interlock
Cancel System . . . . . . . . . . . . . .
Wiring Diagram - VQ40DE Without Clutch Inter-
lock Cancel System . . . . . . . . . . . . .
Wiring Diagram - QR25DE . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ..
STARTING SYSTEM . . . . . . . . . . .
Symptom Table . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ...
STARTER MOTOR . . . . . . . . . . ...
Removal and Installation (QR25DE) . . . . . ...
STR-2
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ...
STARTER MOTOR . . . . . . . . . . .
PRECAUTIONS
STR-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010138396
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Power Generation Variable Voltage Control System
INFOID:0000000009482278
CAUTION:
For this model, the battery current sensor that is installed to the negative battery cable measures the
charging/discharging current of the battery and performs various engine controls. If an electrical com-
ponent is connected directly to the negative battery terminal, the current flowing through that compo-
nent will not be measured by the battery current sensor. This condition may cause a malfunction of
the engine control system and battery discharge may occur. Do not connect an electrical component
or ground wire directly to the battery terminal.
Precaution for Work
INFOID:0000000009482279
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст