Nissan Frontier. Instruction — part 392
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
EC-139
< DTC/CIRCUIT DIAGNOSIS >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
PBIB2318E
EC-140
< DTC/CIRCUIT DIAGNOSIS >
[QR25DE]
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
DETAILED PROCEDURE
1.
CHECK “A/F ALPHA-B1”
1. Start engine.
2. Confirm that the testing conditions are met. Refer to
.
3. Select “A/F ALPHA-B1” in “DATA MONITOR (SPEC)” mode, and make sure that each indication is within
the SP value.
NOTE:
PBIB3213E
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
EC-141
< DTC/CIRCUIT DIAGNOSIS >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Check “A/F ALPHA-B1” for approximately 1 minute because they may fluctuate. It is NG if the indication is
out of the SP value even a little.
OK or NG
OK
>> GO TO 17.
NG (Less than the SP value)>>GO TO 2.
NG (More than the SP value)>>GO TO 3.
2.
CHECK “B/FUEL SCHDL”
Select “B/FUEL SCHDL” in “DATA MONITOR (SPEC)” mode, and make sure that indication is within the SP
value.
OK or NG
OK
>> GO TO 4.
NG (More than the SP value)>>GO TO 19.
3.
CHECK “B/FUEL SCHDL”
Select “B/FUEL SCHDL” in “DATA MONITOR (SPEC)” mode, and make sure that indication is within the SP
value.
OK or NG
OK
>> GO TO 6.
NG (More than the SP value)>>GO TO 6.
NG (Less than the SP value)>>GO TO 25.
4.
CHECK “A/F ALPHA-B1”
1. Stop the engine.
2. Disconnect PCV hose, and then plug it.
3. Start engine.
4. Select “A/F ALPHA-B1” in “DATA MONITOR (SPEC)” mode, and make sure that each indication is within
the SP value.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 6.
5.
CHANGE ENGINE OIL
1. Stop the engine.
2. Change engine oil.
NOTE:
This symptom may occur when a large amount of gasoline is mixed with engine oil because of driving
conditions (such as when engine oil temperature does not rise enough since a journey distance is too
short during winter). The symptom will not be detected after changing engine oil or changing driving con-
ditions.
>> INSPECTION END
6.
CHECK FUEL PRESSURE
Check fuel pressure. (Refer to
OK or NG
OK
>> GO TO 9.
NG (Fuel pressure is too high)>>Replace fuel pressure regulator, refer to
.
GO TO 8.
NG (Fuel pressure is too low)>>GO TO 7.
7.
DETECT MALFUNCTIONING PART
1. Check the following.
-
Clogged and bent fuel hose and fuel tube
-
Clogged fuel filter
-
Fuel pump and its circuit (Refer to
.)
2. If NG, repair or replace the malfunctioning part. (Refer to
If OK, replace fuel pressure regulator.
EC-142
< DTC/CIRCUIT DIAGNOSIS >
[QR25DE]
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
>> GO TO 8.
8.
CHECK “A/F ALPHA-B1”
1. Start engine.
2. Select “A/F ALPHA-B1” in “DATA MONITOR (SPEC)” mode, and make sure that each indication is within
the SP value.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 9.
9.
PERFORM POWER BALANCE TEST
1. Perform “POWER BALANCE” in “ACTIVE TEST” mode.
2. Make sure that the each cylinder produces a momentary engine speed drop.
OK or NG
OK
>> GO TO 12.
NG
>> GO TO 10.
10.
DETECT MALFUNCTIONING PART
1. Check the following below.
-
Ignition coil and its circuit (Refer to
EC-446, "Component Description"
.)
-
Fuel injector and its circuit (Refer to
EC-439, "Component Description"
.)
-
Intake air leakage
-
Low compression pressure (Refer to
.)
2. If NG, repair or replace the malfunctioning part.
If OK, replace fuel injector. (It may be caused by leakage from fuel injector or clogging.)
>> GO TO 11.
11.
CHECK “A/F ALPHA-B1”
1. Start engine.
2. Select “A/F ALPHA-B1” in “DATA MONITOR (SPEC)” mode, and make sure that each indication is within
the SP value.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 12.
12.
CHECK A/F SENSOR 1 FUNCTION
Perform all DTC Confirmation Procedure related with A/F sensor 1.
• For DTC P0130, refer to
EC-197, "DTC Confirmation Procedure"
.
• For DTC P0131, refer to
EC-201, "DTC Confirmation Procedure"
.
• For DTC P0132, refer to
EC-204, "DTC Confirmation Procedure"
.
• For DTC P014C, refer to
• For DTC P014D, refer to
• For DTC P015A, refer to
• For DTC P015B, refer to
• For DTC P2096, refer to
EC-402, "DTC Confirmation Procedure"
.
• For DTC P2097, refer to
EC-402, "DTC Confirmation Procedure"
.
OK or NG
OK
>> GO TO 15.
NG
>> GO TO 13.
13.
CHECK A/F SENSOR 1 CIRCUIT
Perform Diagnostic Procedure according to corresponding DTC.
>> GO TO 14.
14.
CHECK “A/F ALPHA-B1”
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст