Nissan Frontier. Instruction — part 819
DRIVE SHAFT
FAX-13
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
CAUTION:
• The boot may break if the boot installation length is less than the specified value.
• Do not to touch the tip of the suitable tool to the inside of the boot.
8. Secure the big and small ends of the boot with the new boot
bands as shown.
CAUTION:
Do not reuse boot bands.
9. Secure housing and shaft and then make sure that they are in the correct position when rotating boot. Use
a new boot band if the boot band needs to be loosened to reposition the boot.
10. Install circlip and dust cover to housing.
CAUTION:
Do not reuse circlip and dust cover.
Wheel Side
1. Insert the Genuine NISSAN Grease or equivalent, into the joint
sub-assembly serration hole until the grease begins to ooze
from the ball groove and serration hole. Refer to
USA AND CANADA : Fluids and Lubricants"
(United States and
Canada),
MA-18, "FOR MEXICO : Fluids and Lubricants"
(Mex-
ico). After inserting the grease, use a shop cloth to wipe off the
grease that has oozed out.
2. Wrap the serrated part of the shaft with tape. Install the boot
band and boot onto the shaft. Do not damage the boot.
CAUTION:
Do not reuse boot and boot band.
3. Remove the protective tape wound around the serrated part of
the shaft.
Boot installation
length (L)
: Refer to
.
SFA395
SDIA1127E
SFA800
FAX-14
< UNIT DISASSEMBLY AND ASSEMBLY >
DRIVE SHAFT
4. Attach the circlip to the shaft. The circlip must fit securely into
the shaft groove. Attach the nut to the joint sub-assembly.
CAUTION:
Do not reuse circlip.
5. Insert the specified quantity of Genuine NISSAN Grease or
equivalent, into the joint sub-assembly and the large end of the
MA-16, "FOR USA AND CANADA : Fluids and
(United States and Canada),
(Mexico).
CAUTION:
If grease adheres to the boot mounting surface (indicated
by * marks) on shaft and housing, boot may come off.
Remove all grease from surfaces.
6. Install the boot securely into the grooves (indicated by the * marks) as shown.
CAUTION:
If there is grease on the boot mounting surfaces (indicated
by the * marks) of the shaft and joint sub-assembly, the
boot may come off. Remove all grease from the drive shaft
surfaces.
7. Check that the boot installation length (L) is the specified length.
Insert a suitable tool into the big side of the boot. Bleed the air
from the boot to prevent boot deformation.
CAUTION:
• The boot may break if the boot installation length is less than the specified length.
• Do not contact inside surface of boot with the tip of the suitable tool.
8. Secure large and small ends of the boot using new boot bands
using tool as shown.
CAUTION:
Do not reuse boot bands.
RAC0049D
Grease capacity : Refer to
SDIA1446E
Boot installation
length (L)
: Refer to
.
Tool number : KV40107300 ( — )
JPDIF0142ZZ
RAC1133D
DRIVE SHAFT
FAX-15
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Secure boot band so that dimension (M) meets specification
as shown.
9. After installing the housing to the shaft, rotate the boot to check
that it is positioned correctly. If the boot is not positioned cor-
rectly, remove the old boot bands then reposition the boot and
secure the boot with new boot bands.
Dimension (M)
: Refer to
DSF0047D
FAX-16
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000009480032
Drive Shaft
INFOID:0000000009480033
Boot Bands
INFOID:0000000009480034
Unit: mm (in)
Axial end play limit
0.05 mm (0.002 in) or less
Drive shaft joint type
Final drive side
Rzeppa
Wheel side
Rzeppa
Grease
Specification
Genuine NISSAN Grease or equivalent
Capacity
Final drive side
120 - 140 g (4.23 - 4.94 oz)
Wheel side
110 - 130 g (3.88 - 4.59 oz)
Boot installed length (L)
Final drive side
163.9 - 164.3 mm (6.45 - 6.47 in)
Wheel side
135.1 mm (5.32 in)
JPDIF0144ZZ
Dimension (M)
1.0 - 4.0 (0.039 - 0.157)
DSF0047D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст