Nissan Frontier. Instruction — part 1264
PREPARATION
TM-267
< PREPARATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009480663
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
ST2505S001
(J-34301-C)
Oil pressure gauge set
1 ST25051001
( — )
Oil pressure gauge
2 ST25052000
( — )
Hose
3 ST25053000
( — )
Joint pipe
4 ST25054000
( — )
Adapter
5 ST25055000
( — )
Adapter
Measuring line pressure
KV31103600
(J-45674)
Joint pipe adapter
(With ST25054000)
Measuring line pressure
ST33400001
(J-26082)
Drift
• Installing rear oil seal (2WD models)
• Installing oil pump housing oil seal
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
KV31102400
(J-34285 and J-34285-87)
Clutch spring compressor
Installing reverse brake return spring retainer
a: 320 mm (12.60 in)
b: 174 mm (6.85 in)
ST25850000
(J-25721-A)
Sliding hammer
Remove oil pump assembly
a: 179 mm (7.05 in)
b: 70 mm (2.76 in)
c: 40 mm (1.57 in)
d: M12X1.75P
LCIA0399E
ZZA1227D
NT086
NT423
NT422
TM-268
< PREPARATION >
[5AT: RE5R05A]
PREPARATION
Commercial Service Tool
INFOID:0000000009480664
—
(J-47002)
Transmission jack adapter kit
1.
—
(J-47002-1)
Center bracket
2.
—
(J-47002-3)
Adapter plate
3.
—
(J-47002-4)
Adapter block
Assist in removal of transmission and transfer
case as one assembly using only one trans-
mission jack.
—
(J-46534)
Trim Tool Set
Removing and installing trim parts
Tool number
(TechMate No.)
Tool name
Description
WCIA0499E
AWJIA0483ZZ
Tool name
Description
Power tool
Loosening nuts, screws and bolts
Drift
Installing instruction shaft seals
a: 22 mm (0.87 in) dia.
Drift
Installing rear oil seal (4WD models)
a: 64 mm (2.52 in) dia.
Pin punch
• Removing retaining pin
• Installing retaining pin
a: 4 mm (0.16 in) dia.
PIIB1407E
NT083
SCIA5338E
NT410
A/T FLUID
TM-269
< PERIODIC MAINTENANCE >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PERIODIC MAINTENANCE
A/T FLUID
Checking the A/T Fluid (ATF)
INFOID:0000000009480665
CAUTION:
If using the vehicle for towing, the A/T fluid must be replaced as specified. Refer to
AND CANADA : Periodic Maintenance"
(United States and Canada) and
(Mexico).
1. Before driving, the A/T fluid level can be checked at A/T fluid
temperatures of 30
° to 50° C (86° to 122° F) using the “COLD”
range on the A/T fluid level gauge as follows:
a. Park the vehicle on a level surface and set the parking brake.
b. Start the engine and move the selector lever through each gear
position. Shift the selector lever into the “P” position.
c. Check the A/T fluid level with the engine idling.
d. Remove the A/T fluid level gauge and wipe it clean with a lint-
free paper.
CAUTION:
When wiping the A/T fluid from the A/T fluid level gauge,
always use a lint-free paper, not a cloth.
e. Re-insert the A/T fluid level gauge into the A/T fluid charging
pipe until the cap contacts the top of the A/T fluid charging pipe
as shown.
CAUTION:
To check A/T fluid level, insert the A/T fluid level gauge until
the cap contacts the top of the A/T fluid charging pipe, with
the gauge reversed from the normal inserted position.
f.
Remove the A/T fluid level gauge and note the A/T fluid level. If
the A/T fluid level is at low side of range, add A/T fluid to the
transmission through the A/T fluid charging pipe.
CAUTION:
Do not overfill the transmission with A/T fluid.
g. Install the A/T fluid level gauge and the A/T fluid level gauge bolt.
2. Warm up the engine and transmission.
3. Check for any A/T fluid leaks.
4. Drive the vehicle to increase the A/T fluid temperature to 80
° C (176° F).
LLIA0071E
A/T fluid level gauge bolt
: Refer to
SCIA2899E
TM-270
< PERIODIC MAINTENANCE >
[5AT: RE5R05A]
A/T FLUID
5. Allow the A/T fluid temperature to fall to approximately 65
°C (149°F). Use the CONSULT to monitor the A/
T fluid temperature as follows:
NOTE:
The A/T fluid level will be significantly affected by the A/T fluid temperature as shown. Therefore monitor
the A/T fluid temperature data using the CONSULT.
a. Connect CONSULT to data link connector.
b. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT.
c.
Read out the value of “ATF TEMP 1”.
6. Re-check the A/T fluid level at A/T fluid temperatures of approxi-
mately 65
°C (149°F) using the “HOT” range on the A/T fluid
level gauge as shown. The HOT range is between 50
° - 80° C
(122
° - 176° F).
CAUTION:
• When wiping the A/T fluid from the A/T fluid level gauge,
always use lint-free paper, not a cloth.
• To check the A/T fluid level, insert the A/T fluid level
gauge until the cap contacts the top of the A/T fluid charg-
ing pipe, with the gauge reversed from the normal
inserted position as shown.
7. Check the A/T fluid condition.
• If the A/T fluid is very dark or has some burned smell, there
may be an internal problem with the transmission. Flush the
transmission cooling system after repairing the transmission.
• If the A/T fluid contains frictional material (clutches, bands,
etc.), replace the radiator and flush the transmission cooler
lines using cleaning solvent and compressed air after repairing
the transmission.
8. Install the A/T fluid level gauge in the A/T fluid charging pipe.
9. Tighten the A/T fluid level gauge bolt to specification.
SLIA0016E
LLIA0071E
A/T fluid level gauge bolt
: Refer to
SCIA2899E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст