Nissan Frontier. Instruction — part 299
DLN-98
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
TRANSFER CONTROL DEVICE
c.
Tighten the bolts to the specified torque. Refer to
3. Install the breather hose to the transfer control device.
4. Connect the transfer control device connector.
5. After the installation, check the 4WD shift indicator pattern. If
NG, adjust the position between the transfer assembly and
transfer control unit. Refer to
DLN-83, "Precaution for Transfer
Assembly and Transfer Control Unit Replacement"
SDIA2212E
AIR BREATHER HOSE
DLN-99
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000009479716
COMPONENTS
REMOVAL
1. Disconnect air breather hose from transfer control device.
2. Disconnect air breather hose from breather tube (transfer).
3. Release air breather hose clamp and clips as necessary.
4. Disconnect air breather hoses from breather tube.
CAUTION:
Note paint marks for installation.
INSTALLATION
CAUTION:
Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
1. Install each air breather hose into the breather tube (metal con-
nector) until the hose end reaches the end of the curved section.
Set each air breather hose with paint mark facing upward.
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Breather tube (transfer)
7.
Air breather hose clamp
8.
Transfer control device
SDIA3351E
SDIA3299E
DLN-100
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
AIR BREATHER HOSE
2. Install transfer control device air breather hose and transfer air
breather hose on clip A and clip B with the paint mark facing
upward.
3. Install clip C on transfer control device air breather hose and
transfer air breather hose with the paint mark matched.
4. Install transfer control device air breather hose and transfer air
breather hose on clip D with the paint mark facing upward.
5. Install transfer air breather hose (A) into the breather tube
(transfer, metal connector) until the hose end reaches the base
of the tube. Set transfer air breather hose with paint mark (B)
facing upward.
6. Install transfer control device air breather hose into transfer con-
trol device (case connector) until the hose end reaches the base
of the tube. Set transfer control device air breather hose with
paint mark facing forward.
SDIA3353E
SDIA3354E
SDIA3355E
AWDIA0784ZZ
SDIA3300E
TRANSFER ASSEMBLY
DLN-101
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Removal and Installation
INFOID:0000000009479717
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Switch 4WD shift switch to 2WD and set transfer assembly to 2WD.
2. Partially drain the transfer fluid. Refer to
.
3. Remove the transmission under cover (if equipped) using power tool.
4. Remove the center exhaust tube and main muffler. Refer to
EX-6, "Removal and Installation"
.
5. Remove the front and rear propeller shafts. Refer to
DLN-134, "Removal and Installation"
(front) and
143, "Removal and Installation"
DLN-174, "Removal and Installation"
CAUTION:
Do not damage spline, sleeve yoke and rear oil seal when removing rear propeller shaft.
6. Remove insulator nuts from the transmission crossmember. Refer to
TM-74, "Removal and Installation
from Vehicle (For 4WD Models)"
TM-310, "Removal and Installation for VQ40DE 4WD Models"
(A/T).
7. Position two suitable jacks under the transmission and transfer assembly.
8. Remove the transmission crossmember. Refer to
TM-74, "Removal and Installation from Vehicle (For
TM-310, "Removal and Installation for VQ40DE 4WD Models"
(A/T).
WARNING:
Support transmission and transfer assembly using two suitable jacks while removing transmis-
sion crossmember.
9. Disconnect the harness connectors from the following:
• ATP switch
• 4LO switch
• Wait detection switch
• Transfer control device
10. Remove harness from retainers.
11. Disconnect each air breather hose from the following. Refer to
DLN-99, "Removal and Installation"
.
• Transfer control device
• Breather tube (transfer)
12. Remove the transfer to transmission and transmission to transfer bolts.
WARNING:
Support transfer assembly with suitable jack while removing it.
13. Remove the transfer assembly.
CAUTION:
Do not damage transmission rear oil seal (A/T).
INSTALLATION
Installation is in the reverse order of removal.
• Tighten the bolts to specification.
• Fill the transfer with new fluid. Refer to
• Check the transfer fluid. Refer to
.
• Start the engine for one minute. Then stop the engine and recheck
the transfer fluid. Refer to
MA-47, "TRANSFER FLUID : Inspec-
Tightening torque
: 36 N·m (3.7kg-m, 27 ft-lb)
WDIA0510E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст