Nissan Frontier. Instruction — part 168
BRC-200
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
ABS WARNING LAMP
ABS WARNING LAMP
Description
INFOID:0000000009479515
×: ON –: OFF
Component Function Check
INFOID:0000000009479516
1.
CHECK ABS WARNING LAMP OPERATION
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Go to diagnosis procedure. Refer to
BRC-200, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009479517
1.
CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check items displayed by self-diagnosis.
2.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-236, "Removal and Installa-
.
NO
>> Replace combination meter. Refer to
MWI-90, "Removal and Installation"
Special Repair Requirement
INFOID:0000000009479518
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to
BRC-124, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-
>> GO TO 2
2.
CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
BRC-125, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
Condition
ABS warning lamp
Ignition switch OFF
–
For 2 seconds after turning ON ignition switch
×
2 seconds later after turning ON ignition switch
–
ABS function is malfunctioning.
×
EBD function is malfunctioning.
×
BRAKE WARNING LAMP
BRC-201
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
BRAKE WARNING LAMP
Description
INFOID:0000000009479519
×: ON –: OFF
NOTE:
• 1: Brake warning lamp will turn on in case of parking brake operation (when switch is ON) or of brake fluid level switch operation
(when brake fluid is insufficient).
• 2: After starting engine, brake warning lamp is turned off.
Component Function Check
INFOID:0000000009479520
1.
BRAKE WARNING LAMP OPERATION CHECK
Check that the lamp illuminates after the ignition switch is turned ON, and turns OFF after the engine is
started.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Go to diagnosis procedure. Refer to
BRC-201, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009479521
1.
CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. refer to
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check items displayed by self-diagnosis.
2.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-236, "Removal and Installa-
.
NO
>> Replace combination meter. Refer to
MWI-90, "Removal and Installation"
Special Repair Requirement
INFOID:0000000009479522
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to
BRC-124, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-
>> GO TO 2
2.
CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
BRC-125, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
Condition
Brake warning lamp (Note 1)
Ignition switch OFF
–
Ignition switch ON
× (Note 2)
EBD function is malfunctioning.
×
BRC-202
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
HILL DESCENT CONTROL INDICATOR LAMP
HILL DESCENT CONTROL INDICATOR LAMP
Description
INFOID:0000000009479523
×: ON –: OFF
Component Function Check
INFOID:0000000009479524
1.
CHECK HILL DESCENT CONTROL INDICATOR LAMP OPERATION
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Go to diagnosis procedure. Refer to
BRC-202, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009479525
1.
CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check items displayed by self-diagnosis.
2.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-236, "Removal and Installa-
.
NO
>> Replace combination meter. Refer to
MWI-90, "Removal and Installation"
Special Repair Requirement
INFOID:0000000009479526
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to
BRC-124, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-
>> GO TO 2
2.
CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
BRC-125, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
Condition
Hill descent control indicator lamp
Ignition switch OFF
–
For 2 seconds after turning ON ignition switch
×
2 seconds later after turning ON ignition switch
–
Hill descent control function is malfunctioning.
–
VDC OFF INDICATOR LAMP
BRC-203
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
VDC OFF INDICATOR LAMP
Description
INFOID:0000000009479527
×: ON –: OFF
Component Function Check
INFOID:0000000009479528
1.
VDC OFF INDICATOR LAMP OPERATION CHECK 1
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Go to diagnosis procedure. Refer to
BRC-203, "Diagnosis Procedure"
.
2.
VDC OFF INDICATOR LAMP OPERATION CHECK 2
Check that the VDC OFF indicator lamp in the combination meter turns ON/OFF correctly when operating the
VDC OFF switch.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Check VDC OFF switch. Refer to
BRC-198, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009479529
1.
CHECK VDC OFF SWITCH
Check that the VDC OFF indicator lamp in the combination meter turns ON/OFF correctly when operating the
VDC OFF switch.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check VDC OFF switch. Refer to
BRC-198, "Diagnosis Procedure"
.
2.
CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Check items displayed by self-diagnosis.
3.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-236, "Removal and Installa-
.
NO
>> Replace combination meter. Refer to
MWI-90, "Removal and Installation"
Condition
VDC OFF indicator lamp
Ignition switch OFF
–
For 2 seconds after turning ON ignition switch
×
2 seconds later after turning ON ignition switch
–
VDC OFF switch turned ON. (VDC function is OFF.)
×
VDC/TCS function is malfunctioning.
×
ABS function is malfunctioning.
×
EBD function is malfunctioning.
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст