Nissan Frontier. Instruction — part 125

BRC-28

< SYSTEM DESCRIPTION >

[TYPE 1]

EBD

Component Description

INFOID:0000000009479251

10. Rear wheel sensor LH C11

Rear wheel sensor RH C10

11.

Steering angle sensor (behind spiral ca-
ble) M47
(Steering wheel removed for clarity)

12. VDC OFF switch M154

13. Stop lamp switch (with M/T) E38

Stop lamp switch (with A/T) E39

Component parts

Reference

ABS actuator and electric unit (control unit)

Pump

BRC-46, "Description"

Motor

Actuator relay

BRC-62, "Description"

Solenoid valve

BRC-55, "Description"

VDC switch-over valve
(CV1, CV2, SV1, SV2)

BRC-73, "Description"

Wheel sensor

BRC-50, "Description"

Yaw rate/side/decel G sensor

BRC-48, "Description"

Stop lamp switch

BRC-53, "Description"

Steering angle sensor

BRC-64, "Description"

Brake fluid level switch

BRC-67, "Description"

VDC OFF switch

BRC-78, "Description"

ABS warning lamp

BRC-80, "Description"

Brake warning lamp

BRC-81, "Description"

VDC OFF indicator lamp

BRC-82, "Description"

SLIP indicator lamp

BRC-84, "Description"

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL

UNIT)]

BRC-29

< SYSTEM DESCRIPTION >

[TYPE 1]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]

CONSULT Function (ABS)

INFOID:0000000009479252

FUNCTION

CONSULT can display each diagnostic item using the following direct diagnostic modes.

SELF DIAGNOSTIC RESULT

Operation Procedure

1. Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for

approximately 1 minute.

How to Erase Self-diagnosis Results

1. After erasing DTC memory, start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately

1 minute as the final inspection, and make sure that the ABS warning lamp, VDC OFF indicator lamp,

SLIP indicator lamp and brake warning lamp turn OFF.

CAUTION:

If memory cannot be erased, perform applicable diagnosis.

NOTE:

• When the wheel sensor malfunctions, after inspecting the wheel sensor system, the ABS warning lamp,

VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp will not turn OFF even when the

system is normal unless the vehicle is driving at approximately 30 km/h (19 MPH) or more for approxi-

mately 1 minute.

• Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or of brake fluid

level switch operation (when brake fluid is insufficient).

• VDC OFF switch should not stay “ON” position.

Display Item List

Refer to

BRC-90, "DTC No. Index"

.

DATA MONITOR

Direct Diagnostic Mode

Description

ECU Identification

The ABS actuator and electric unit (control unit) part number is displayed.

Self Diagnostic Result

The ABS actuator and electric unit (control unit) self diagnostic results are displayed.

Data Monitor

The ABS actuator and electric unit (control unit) input/output data is displayed in real time.

Active Test

The ABS actuator and electric unit (control unit) activates outputs to test components.

Work support

The settings for ABS actuator and electric unit (control unit) functions can be changed.

CAN Diag Support Mntr

The result of transmit/receive diagnosis of CAN communication is displayed.

Item

(Unit)

Data monitor item selection

Remarks

ECU INPUT

SIGNALS

MAIN

SIGNALS

SELECTION

FROM MENU

FR LH SENSOR
(km/h, mph)

×

×

×

Wheel speed calculated by front LH
wheel sensor signal is displayed.

FR RH SENSOR
(km/h, mph)

×

×

×

Wheel speed calculated by front RH
wheel sensor signal is displayed.

RR LH SENSOR
(km/h, mph)

×

×

×

Wheel speed calculated by rear LH
wheel sensor signal is displayed.

RR RH SENSOR
(km/h, mph)

×

×

×

Wheel speed calculated by rear RH
wheel sensor signal is displayed.

DECEL G-SEN
(G)

×

×

×

Longitudinal acceleration detected
by decel G-sensor is displayed.

BRC-30

< SYSTEM DESCRIPTION >

[TYPE 1]

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL

UNIT)]

FR RH IN SOL
(ON/OFF)

–

×

×

Front RH IN ABS solenoid (ON/
OFF) status is displayed.

FR RH OUT SOL
(ON/OFF)

–

×

×

Front RH OUT ABS solenoid (ON/
OFF) status is displayed.

FR LH IN SOL
(ON/OFF)

–

×

×

Front LH IN ABS solenoid (ON/
OFF) status is displayed.

FR LH OUT SOL
(ON/OFF)

–

×

×

Front LH OUT ABS solenoid (ON/
OFF) status is displayed.

RR RH IN SOL
(ON/OFF)

–

×

×

Rear RH IN ABS solenoid (ON/
OFF) status is displayed.

RR RH OUT SOL
(ON/OFF)

–

×

×

Rear RH OUT ABS solenoid (ON/
OFF) status is displayed.

RR LH IN SOL
(ON/OFF)

–

×

×

Rear LH IN ABS solenoid (ON/OFF)
status is displayed.

RR LH OUT SOL
(ON/OFF)

–

×

×

Rear LH OUT ABS solenoid (ON/
OFF) status is displayed.

EBD WARN LAMP
(ON/OFF)

–

–

×

Brake warning lamp (ON/OFF) sta-
tus is displayed.

STOP LAMP SW
(ON/OFF)

×

×

×

Stop lamp switch (ON/OFF) status
is displayed.

MOTOR RELAY
(ON/OFF)

–

×

×

ABS motor relay signal (ON/OFF)
status is displayed.

ACTUATOR RLY
(ON/OFF)

–

×

×

ABS actuator relay signal (ON/OFF)
status is displayed.

ABS WARN LAMP
(ON/OFF)

–

×

×

ABS warning lamp (ON/OFF) status
is displayed.

OFF LAMP
(ON/OFF)

–

×

×

OFF Lamp (ON/OFF) status is dis-
played.

OFF SW
(ON/OFF)

×

×

×

VDC OFF switch (ON/OFF) status
is displayed.

SLIP LAMP
(ON/OFF)

–

×

×

SLIP indicator lamp (ON/OFF) sta-
tus is displayed.

BATTERY VOLT
(V)

×

×

×

Voltage supplied to ABS actuator
and electric unit (control unit) is dis-
played.

GEAR
(1, 2, 3, 4, 5)

×

×

×

Gear position determined by TCM is
displayed.

SLCT LVR POSI
(P, R, N, D)

×

×

×

Shift position judged by PNP switch
signal.

ENGINE SPEED
(rpm)

×

×

×

Engine speed judged by CAN com-
munication signal is displayed.

YAW RATE SEN
(d/s)

×

×

×

Yaw rate detected by yaw rate sen-
sor is displayed.

R POSI SIG
(ON/OFF)

–

–

×

Shift position judged by PNP switch
signal.

N POSI SIG
(ON/OFF)

–

–

×

Shift position judged by PNP switch
signal.

P POSI SIG
(ON/OFF)

–

–

×

Shift position judged by PNP switch
signal.

Item

(Unit)

Data monitor item selection

Remarks

ECU INPUT

SIGNALS

MAIN

SIGNALS

SELECTION

FROM MENU

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL

UNIT)]

BRC-31

< SYSTEM DESCRIPTION >

[TYPE 1]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

×: Applicable
–: Not applicable

WORK SUPPORT

CV1
(ON/OFF)

–

–

×

Front side switch-over solenoid
valve (cut valve) (ON/OFF) status is
displayed.

CV2
(ON/OFF)

–

–

×

Rear side switch-over solenoid
valve (cut-valve) (ON/OFF) status is
displayed.

SV1
(ON/OFF)

–

–

×

Front side switch-over solenoid
valve (suction valve) (ON/OFF) sta-
tus is displayed.

SV2
(ON/OFF)

–

–

×

Rear side switch-over solenoid
valve (suction valve) (ON/OFF) sta-
tus is displayed.

2WD/4WD
(2WD/4WD)

–

–

×

It recognizes on software whether it
is 2WD and whether it is in 4WD
state.

ACCEL POS SIG
(%)

×

–

×

Throttle valve open/close status
judged by CAN communication sig-
nal is displayed.

SIDE G-SENSOR
(m/s

2

)

×

–

×

Transverse acceleration detected
by side G-sensor is displayed.

STR ANGLE SIG
(deg)

×

–

×

Steering angle detected by steering
angle sensor is displayed.

PRESS SENSOR
(bar)

×

–

×

Brake pressure detected by pres-
sure sensor is displayed.

EBD SIGNAL
(ON/OFF)

–

–

×

EBD operation (ON/OFF) status is
displayed.

ABS SIGNAL
(ON/OFF)

–

–

×

ABS operation (ON/OFF) status is
displayed.

TCS SIGNAL
(ON/OFF)

–

–

×

TCS operation (ON/OFF) status is
displayed.

VDC SIGNAL
(ON/OFF)

–

–

×

VDC operation (ON/OFF) status is
displayed.

ABS FAIL SIG
(ON/OFF)

–

–

×

ABS fail signal (ON/OFF) status is
displayed.

TCS FAIL SIG
(ON/OFF)

–

–

×

TCS fail signal (ON/OFF) status is
displayed.

VDC FAIL SIG
(ON/OFF)

–

–

×

VDC fail signal (ON/OFF) status is
displayed.

CRANKING SIG
(ON/OFF)

–

–

×

The input state of the key SW
START position signal is displayed.

FLUID LEV SW
(ON/OFF)

×

–

×

Brake fluid level switch (ON/OFF)
status is displayed.

Item

(Unit)

Data monitor item selection

Remarks

ECU INPUT

SIGNALS

MAIN

SIGNALS

SELECTION

FROM MENU