Nissan Frontier. Instruction — part 1314
WT-4
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
3.
SELF-DIAGNOSIS
Perform self-diagnosis. Refer to
WT-32, "Self-Diagnosis (With CONSULT)"
WT-13, "Self-Diagnosis (Without
>> GO TO 4
4.
SYMPTOM
>> GO TO 5
5.
MALFUNCTIONING PARTS
Repair or replace the applicable parts.
>> GO TO 6
6.
DRIVE TEST
1. Perform a drive test.
2. Check the low tire pressure warning lamp.
>> GO TO 7
7.
SELF-DIAGNOSIS
Perform self-diagnosis. Refer to
WT-32, "Self-Diagnosis (With CONSULT)"
WT-13, "Self-Diagnosis (Without
Are any DTCs displayed?
YES
>> GO TO 5
NO
>> Inspection End.
INSPECTION AND ADJUSTMENT
WT-5
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
INSPECTION AND ADJUSTMENT
Preliminary Check
INFOID:0000000009480240
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
1.
TIRE PRESSURE
Check all tire pressures. Refer to
Do tire pressures match specification?
YES
>> GO TO 2.
NO
>> Adjust tire pressures to specified value.
2.
LOW TIRE PRESSURE WARNING LAMP
Check low tire pressure warning lamp activation.
Does the low tire pressure warning lamp activate for one second when ignition switch is turned ON?
YES
>> GO TO 3.
NO
WT-39, "Low Tire Pressure Warning Lamp Does Not Come On When Ignition Switch Is
.
3.
BCM CONNECTOR
1. Disconnect BCM harness connectors.
2. Check terminals for damage or loose connections.
3. Reconnect harness connectors.
Are BCM connectors damaged or loose?
YES
>> Repair or replace damaged parts.
NO
>> GO TO 4.
4.
TRANSMITTER ACTIVATION TOOL
Check battery in transmitter activation tool.
Is transmitter activation tool battery fully charged?
YES
>> Perform self-diagnosis. Refer to
WT-32, "Self-Diagnosis (With CONSULT)"
NO
>> Replace battery in transmitter activation tool.
WT-6
< BASIC INSPECTION >
ID REGISTRATION PROCEDURE
ID REGISTRATION PROCEDURE
Description
INFOID:0000000009480241
This procedure must be performed after replacement of a transmitter, BCM or rotation of the wheels.
Work Procedure
INFOID:0000000009480242
TPMS ID registration can be performed using one of the following procedures:
• Transmitter Activation tool (J-45295-A) with CONSULT (preferred method)
• Signal Tech II tool (J-50190) with CONSULT (preferred method)
• Signal Tech II tool (J-50190) without CONSULT
• CONSULT only
TPMS REGISTRATION WITH TRANSMITTER ACTIVATION TOOL (J-45295-A)
With CONSULT
1. Turn the ignition switch ON.
2. Using CONSULT, select “WORK SUPPORT” in BCM (AIR PRESSURE MONITOR). Then, select “ID
REGIST.”
3. Select “Start” on “ID REGIST” screen.
4. Hold the transmitter activation tool (J-45295-A) (1) against the
side of the left front tire, near the valve stem.
5. With the tool held at a 0 to 15 degree angle to the tire, press and
hold the transmitter activation tool button until the indicator lamp
turns OFF (approximately 5 seconds).
6. Repeat steps 4 and 5 for the remaining tires in this order: right
front, right rear and left rear.
7. When ID registration is complete, check the following pattern at each wheel.
8. After the ID registration procedure for all wheels is complete, press “End” on the CONSULT to finish ID
registration.
9. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
TPMS REGISTRATION WITH SIGNAL TECH II TOOL (J-50190)
NOTE:
The Signal Tech II must be updated with software version 1.1.48 or newer in order to perform the below proce-
dures. The Signal Tech II software updates can only be downloaded from a CONSULT unit with ASIST. Other
versions of ASIST will not show the updates.
With CONSULT
1. Adjust the tire pressure for all tires to the recommended value. Refer to
.
2. Turn the ignition switch ON.
3. Using CONSULT, select “WORK SUPPORT” in BCM (AIR PRESSURE MONITOR). Then, select “ID
REGIST.”
4. Select “Start” on “ID REGIST” screen.
5. Turn on the Signal Tech II tool (J-50190).
NNEIC0020ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front LH
2 blinks
“Yet (red)”
↓
“Done (green)”
2
Front RH
3
Rear RH
4
Rear LH
ID REGISTRATION PROCEDURE
WT-7
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
6. Hold the Signal Tech II against the side of the left front tire, near
the valve stem.
7. With the tool held at a 0 to 15 degree angle to the tire, select
“Activate Sensor” from the main menu, then press and release
the “OK” button to activate the sensor. Once the sensor is acti-
vated, the vehicle parking lamps will flash and the sensor ID will
appear on the CONSULT screen.
8. Repeat steps 6 and 7 for the remaining tires in this order: right
front, right rear and left rear.
9. When ID registration is complete, check the following pattern at
each wheel.
10. Once all sensors have been activated, select “End” on the CONSULT to finish ID registration.
11. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
Without CONSULT
1. Adjust the tire pressure for all tires to the recommended value. Refer to
2. Turn on the Signal Tech II tool (J-50190) and select “TPMS Check” from the main menu.
3. Select vehicle model and year.
4. When prompted, hold the Signal Tech II against the side of the
left front tire, near the valve stem.
5. With the tool held at a 0 to 15 degree angle to the tire, press and
release the “OK” button to activate the sensor. Once the sensor
is activated, the tool will sound a tone and the tire pressure will
be displayed.
6. Repeat steps 4 and 5 for the remaining tires in this order: right
front, right rear and left rear.
7. When prompted, connect the tool to the data link connector. The
tool will connect to the BCM, read the VIN, read sensor IDs and
check for TPMS DTCs. Along with DTCs detected, one of the
following will be displayed next to each wheel:
-
N/A - Not applicable because no ID found by the tool
-
OK - Wheel and sensor are in original position
-
NEW - New ID found compared to BCM
-
RT - Wheel has been rotated
-
Low Press - Low tire pressure
8. If no DTC is present or the repair has been completed, press the “OK” button to register the IDs and clear
DTCs.
9. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
10. Print a Signal Tech II Audit Report for your records. Refer to the Signal Tech II User Guide for instructions.
TPMS REGISTRATION WITH CONSULT ONLY
With CONSULT
1. Adjust the tire pressure for all wheels to match the list below.
ALEIA0177ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front LH
2 blinks
“Yet (red)”
↓
“Done (green)”
2
Front RH
3
Rear RH
4
Rear LH
ALEIA0177ZZ
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
240 (2.4, 35)
Front RH
220 (2.2, 32)
Rear RH
200 (2.0, 29)
Rear LH
180 (1.8, 26)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст