Nissan Frontier. Instruction — part 253
DLK-58
< DTC/CIRCUIT DIAGNOSIS >
MAP LAMP AND IGNITION KEYHOLE ILLUMINATION FUNCTION
MAP LAMP AND IGNITION KEYHOLE ILLUMINATION FUNCTION
Diagnosis Procedure
INFOID:0000000009478926
1.
CHECK MAP LAMP OPERATION
When room lamp switch is in "DOOR" position, open the driver or passenger door.
Map lamp and ignition keyhole illumination should illuminate.
Is the inspection result normal?
YES
>> Map lamp circuit is OK.
NO
>> Check map lamp circuit. Refer to
KEYFOB ID SET UP WITH CONSULT
DLK-59
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB ID SET UP WITH CONSULT
ID Code Entry Procedure
INFOID:0000000009478927
KEYFOB ID SET UP WITH CONSULT
NOTE:
• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A spe-
cific ID code can be erased with CONSULT. However, when the ID code of a lost keyfob is not known,
all controller ID codes should be erased. After all ID codes are erased, the ID codes of all remaining
and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If
five ID codes are stored in memory when an additional code is registered, only the oldest code is
erased. If less than five codes are stored in memory when an additional code is registered, the new
ID code is added and no ID codes are erased.
• Entry of a maximum of five ID codes is allowed. When more than five codes are entered, the oldest ID
code will be erased.
• Even if the same ID code that is already in memory is input, the same ID code can be entered. The
code is counted as an additional code.
1. Turn ignition switch ON.
2. Select “BCM”.
3. Select “MULTIREMOTE ENT”.
4. Select “WORK SUPPORT”.
5. You can register, erase or confirm a keyfob ID code. To register a new code, select the following option
and follow CONSULT instructions:
• “REMO CONT ID REGIST”
Use this item to register a keyfob ID code.
NOTE:
Register the ID code when keyfob or BCM is replaced, or when an additional keyfob is required.
• “REMO CONT ID ERASUR”
Use this item to erase a keyfob ID code.
• “REMO CONT ID CONFIR”
Use this item to confirm if a keyfob ID code is registered or not.
DLK-60
< DTC/CIRCUIT DIAGNOSIS >
KEYFOB ID SET UP WITHOUT CONSULT
KEYFOB ID SET UP WITHOUT CONSULT
ID Code Entry Procedure
INFOID:0000000009478928
KEYFOB ID SET UP WITHOUT CONSULT
NOTE:
• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A specific ID
code can be erased with CONSULT. However, when the ID code of a lost keyfob is not known, all controller
LIIA1670E
KEYFOB ID SET UP WITHOUT CONSULT
DLK-61
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or new keyfobs
must be re-registered.
To erase all ID codes in memory, register one ID code (keyfob) five times. After all ID codes are erased, the
ID codes of all remaining and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If five ID
codes are stored in memory, when an additional code is registered, only the oldest code is erased. If less
than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is added
and no ID codes are erased.
• If you need to activate more than two additional new keyfobs, repeat the procedure “Additional ID code
entry” for each new keyfob.
• Entry of maximum five ID codes is allowed. When more than five ID codes are entered, the oldest ID code
will be erased.
• Even if same ID code that is already in the memory is input, the same ID code can be entered. The code is
counted as an additional code.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст