Nissan Frontier. Instruction — part 599
PRECAUTIONS
EC-967
< PRECAUTION >
[VQ40DE FOR MEXICO]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
• B1 indicates the bank 1, B2 indicates the bank 2 as shown in
the figure.
• Never operate fuel pump when there is no fuel in lines.
• Tighten fuel hose clamps to the specified torque.
• Never depress accelerator pedal when starting.
• Immediately after starting, never rev up engine unnecessarily.
• Never rev up engine just prior to shutdown.
• When installing C.B. ham radio or a mobile phone, always
observe the following as it may adversely affect electronic
control systems depending on installation location.
- Keep the antenna as far as possible from the electronic con-
trol units.
- Keep the antenna feeder line more than 20 cm (8 in) away
from the harness of electronic controls.
Never let them run parallel for a long distance.
- Adjust the antenna and feeder line so that the standing-wave
radio can be kept smaller.
SEC893C
BBIA0529E
SEF709Y
SEF708Y
EC-968
< PRECAUTION >
[VQ40DE FOR MEXICO]
PRECAUTIONS
- Always ground the radio to vehicle body.
PBIB1512E
PREPARATION
EC-969
< PREPARATION >
[VQ40DE FOR MEXICO]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009481676
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
EG17650301
(J-33984-A)
Radiator cap tester
adapter
Adapts radiator cap tester to radiator cap and radi-
ator filler neck
a: 28 (1.10) dia.
b: 31.4 (1.236) dia.
c: 41.3 (1.626) dia.
Unit: mm (in)
(J-44321)
Fuel pressure gauge
kit
Checks fuel pressure
(J-44321-6)
Fuel pressure adapter
Connects fuel pressure gauge to quick connector
type fuel lines.
(J-45488)
Quick connector re-
lease
Removes fuel tube quick connectors in engine
room
S-NT564
LEC642
LBIA0376E
PBIC0198E
EC-970
< PREPARATION >
[VQ40DE FOR MEXICO]
PREPARATION
Commercial Service Tool
INFOID:0000000009481677
Tool name
(Kent-Moore No.)
Description
Leak detector
i.e.: (J-41416)
Locates the EVAP leak
EVAP service port
adapter
i.e.: (J-41413-OBD)
Applies positive pressure through EVAP service
port
Fuel filler cap adapter
i.e.: (MLR-8382)
Checks fuel tank vacuum relief valve opening
pressure
Socket wrench
Removes and installs engine coolant temperature
sensor
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12)
Reconditions the exhaust system threads before
installing a new oxygen sensor. Use with anti-
seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for Zirco-
nia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for Tita-
nia Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL specifica-
tion MIL-A-907)
Lubricates oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
S-NT703
S-NT704
S-NT815
S-NT705
AEM488
S-NT779
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст