Nissan Frontier. Instruction — part 758
ENGINE UNIT
EM-221
< UNIT DISASSEMBLY AND ASSEMBLY >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4. Remove pilot converter (A/T models) using Tool as necessary.
5. Lift engine, and mount to engine stand.
CAUTION:
• Use an engine stand that has a load capacity [approxi-
mately 240kg (529 lb) or more] large enough for support-
ing the engine weight.
• Before removing the hanging chains, make sure the
engine stand is stable and there is no risk of overturning.
•
6. Drain engine oil. Refer to
Tool number
: ST16610001 (J-23907)
WBIA0583E
PBIC0805E
EM-222
< UNIT DISASSEMBLY AND ASSEMBLY >
[VQ40DE]
ENGINE UNIT
7. Drain engine coolant by removing the cylinder block drain plugs
(A), (B), (C) and (D) from cylinder block as shown.
NOTE:
For Canada, (D) is not plug but block heater.
8. Remove cylinder head. Refer to
EM-205, "Removal and Installation"
9. Remove sub harness, and remove knock sensors.
CAUTION:
Handle sensor carefully; do not shock or drop.
10. Remove piston and connecting rod assembly as follows:
• Before removing piston and connecting rod assembly, check the connecting rod side clearance. Refer to
EM-230, "Inspection After Disassembly"
CAUTION:
Be careful not to drop connecting rod bearing or scratch the bearing surface.
11. Position crankshaft pin corresponding to connecting rod to be removed onto the bottom dead center.
12. Remove connecting rod bearing cap.
13. Push piston and connecting rod assembly out of the cylinder
head side using suitable tool.
CAUTION:
Be careful not to damage the cylinder wall or crankshaft pin
resulting from an interference of the connecting rod big
end.
14. Remove connecting rod bearings from connecting rod and connecting rod bearing cap.
CAUTION:
Identify installation position, and store them without mixing them up.
15. Remove piston rings from piston.
• Before removing piston rings, check the piston ring side clearance. Refer to
.
WLIA0020E
PBIC2940E
ENGINE UNIT
EM-223
< UNIT DISASSEMBLY AND ASSEMBLY >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Remove piston rings using piston ring expander or suitable
tool.
CAUTION:
• When removing piston rings, be careful not to damage
piston.
• Be careful not to damage piston rings by expanding them
excessively.
16. Remove piston from connecting rod as follows:
a. Remove snap ring using snap ring pliers.
b. Heat piston to 60
° to 70°C (140° to 158°F) with industrial use
drier or equivalent.
c. Push out piston pin with a drift which has an outer diameter of
approximately 20 mm (0.79 in).
17. Remove lower cylinder block bolts.
• Before loosening lower cylinder block bolts, measure the crankshaft end play. Refer to
.
PBIC0087E
PBIC1638E
PBIC1639E
PBIC0262E
EM-224
< UNIT DISASSEMBLY AND ASSEMBLY >
[VQ40DE]
ENGINE UNIT
• Loosen lower cylinder block bolts in reverse order as shown in
several different steps.
NOTE:
Use socket (size E14) for bolts No. 1 to 16 (M10 bolt).
18. Remove lower cylinder block.
• Cut liquid gasket for removal. Refer to
EM-120, "Precaution for Liquid Gasket"
CAUTION:
Be careful not to damage the mounting surfaces.
19. Remove crankshaft.
20. Pull rear oil seal out from rear end of crankshaft.
NOTE:
When replacing rear oil seal without removing lower cylinder block, use a suitable tool to pull the rear oil
seal installed between crankshaft and cylinder block out.
CAUTION:
Be careful not to damage crankshaft or cylinder block.
21. Remove main bearings and thrust bearings from cylinder block and lower cylinder block.
CAUTION:
• Do not drop main bearing, or scratch the surface.
• Identify installation positions, and store them without mixing them up.
22. Remove oil jet.
ASSEMBLY
1. Fully air-blow engine coolant and engine oil passages in cylinder block, cylinder bore and crankcase to
remove any foreign material.
WARNING:
Use goggles to protect your eyes.
PBIC2941E
Tool number
: KV10111100 (J-37228)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст