Nissan Frontier. Instruction — part 313
DLN-154
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 3S1310]
REAR PROPELLER SHAFT
UNIT DISASSEMBLY AND ASSEMBLY
REAR PROPELLER SHAFT
Disassembly and Assembly
INFOID:0000000009479747
DISASSEMBLY
Journal
1. Remove the propeller shaft assembly from the vehicle. Refer to
DLN-152, "Removal and Installation"
2. Put matching marks on the rear propeller shaft tube and flange
yoke as shown.
CAUTION:
For matching marks use paint. Do not damage the rear pro-
peller shaft or flange yoke.
3. Remove the snap rings.
CAUTION:
Do not reuse snap rings.
4. Push out and remove the journal bearing by lightly tapping the
yoke with a hammer, taking care not to damage the journal or
yoke hole.
5. Remove the bearing at the opposite side of above operation.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
SPD128
APD011
SPD732
SPD131
REAR PROPELLER SHAFT
DLN-155
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 3S1310]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Center Support Bearing
1. Remove the propeller shaft assembly from the vehicle. Refer to
DLN-152, "Removal and Installation"
.
2. Put matching marks on the propeller shaft tube and the slip
yoke.
CAUTION:
For matching marks, use paint. Do not damage the propel-
ler shaft tube or slip yoke.
3. Remove and discard the clamp near the center support bearing,
then slide the slip yoke off of propeller shaft tube.
4. Press the center support bearing off the propeller shaft tube
using Tool and suitable hydraulic press.
ASSEMBLY
Journal
1. Assemble the journal bearings. Apply multipurpose grease on
the bearing inner surface.
NOTE:
During assembly, use caution so that the needle bearings do not
fall down.
2. Select snap rings that will provide the specified play in an axial
direction of the journal, and install them. Refer to
.
CAUTION:
Do not reuse snap rings.
NOTE:
Select snap rings with a difference in thickness at both sides
within 0.02 mm (0.0008 in).
LDIA0151E
Tool number
: 205-D002
LDIA0152E
WPD019
APD012
DLN-156
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 3S1310]
REAR PROPELLER SHAFT
3. Adjust the thrust clearance between the bearing and snap ring
to zero by tapping the yoke.
4. Make sure that the journal moves smoothly and is below the
joint flex effort specification. Refer to
.
Center Support Bearing
1. Apply a thin coat of multi-purpose grease to both the propeller shaft tube and the inside surface of the
center support bearing.
2. Install the center support bearing on the propeller shaft tube
using a suitable pipe pressing on the inner race.
3. Install a new clamp over the boot on the slip yoke.
4. Align the matching marks and install the slip yoke on the propel-
ler shaft tube.
5. Clean the surfaces and position the boot over the propeller shaft tube and tighten the clamp.
SPD732
LDIA0119E
LDIA0153E
LDIA0151E
REAR PROPELLER SHAFT
DLN-157
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 3S1310]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
6. Install the center support bearing bracket, then install the rear
propeller shaft assembly in the vehicle. Refer to
WDIA0066E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст