Nissan Maxima. Instruction — part 1023
FRONT SEAT
SE-65
< REMOVAL AND INSTALLATION >
[WITH CLIMATE CONTROLLED SEATS]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REMOVAL AND INSTALLATION
FRONT SEAT
Exploded View
INFOID:0000000009468144
DRIVER
Driver Seat - With Climate Controlled Seats
AWJIA0925ZZ
1.
Seatback board
2.
Seatback board clip
3.
Seat cushion lower rear finisher
4.
Seat harness
5.
Seat cushion inner finisher inside (RH) 6.
Recline mechanism inner cover
7.
Seat cushion outer finisher (RH)
8.
Seat belt buckle
9.
Seat cushion assembly
SE-66
< REMOVAL AND INSTALLATION >
[WITH CLIMATE CONTROLLED SEATS]
FRONT SEAT
PASSENGER
10. Seat cushion trim
11. Seat cushion pad
12. Thigh extension tether
13. Thigh extension assembly
14. Climate controlled seat control unit
15. Seat cushion front finisher
16. Front slide cover
17. Clip
18. Power seat control unit
19. Seat cushion thermal electric device
(TED)
20. Lower seat duct
21. Climate controlled seat blower
filter
22. Climate controlled seat blower motor
assembly
23. Seat frame assembly
24. Rear slide cover
25. Power seat switch
26. Seat slide and lifter switch knob
27. Seat recline knob
28. Lumbar support switch
29. Seat cushion outer finisher (LH)
30. Recline device outer cover
31. Seat cushion inner finisher inside
(LH)
32. Seatback assembly
33. Side air bag module
34. Seatback thermal electric device
(TED)
35. Upper seat duct
36. Headrest holder (locked)
37. Headrest holder (free)
38. Seatback frame
39. Seatback trim
40. Seatback pad
41. Headrest
42. Chute rod
FRONT SEAT
SE-67
< REMOVAL AND INSTALLATION >
[WITH CLIMATE CONTROLLED SEATS]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Passenger Seat
AWJIA0926ZZ
1.
Seatback board
2.
Seatback board clips
3.
Headrest
4.
Seat harness
5.
Seat cushion inner finisher inside (RH) 6.
Recline device inner cover
7.
Seat cushion outer finisher (RH) 8.
Seat recline knob
9.
Seat slide and lifter switch knob
10.
Power seat switch
11.
Seat cushion assembly
12. Seat cushion front finisher
13.
Front slide cover
14.
Seat frame assembly
15. Seat cushion outer finisher (LH)
16
Recline mechanism inner cover
17.
Seat cushion inner finisher inside (LH) 18. Seat belt buckle
19.
Seatback assembly
20.
Seatback pad
21. Seatback trim
22.
Seatback frame
23.
Chute rod
24. Side air bag module
25.
Rear slide cover
26.
Headrest holder (locked)
27. Headrest holder (free)
SE-68
< REMOVAL AND INSTALLATION >
[WITH CLIMATE CONTROLLED SEATS]
FRONT SEAT
Removal and Installation
INFOID:0000000009468145
REMOVAL
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seat repair. It can lead to per-
sonal injury if the side air bag module should accidentally deploy.
CAUTION:
• When removing or installing the seat trim, handle it carefully to keep dirt out and to avoid damage.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag module to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After the front side air bag module inflates, the front seatback assembly must be replaced.
• When removing and installing the seat, use shop cloths to protect components from damage.
• Before removing the front seat, turn the ignition switch OFF, disconnect both battery terminals and
wait at least three minutes.
1. Slide the seat to the full forward position.
2. Remove the rear slide covers.
a. Release the pawls (A).
b. Remove the rear slide covers.
3. Remove the rear mount bolts.
4. Slide the seat to the full rearward position.
5. Remove the front slide covers.
6. Remove the front mount bolts.
7. Disconnect the negative and positive battery terminals and wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
ALIIA0356ZZ
ALIIA0324ZZ
ALIIA0323ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст