Nissan Maxima. Instruction — part 853
MWI
COMPASS
MWI-27
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
COMPASS
Description
INFOID:0000000010049563
DESCRIPTION
With the ignition switch in the ON position, and the mode (N) switch
ON, the compass display will indicate the direction the vehicle is
heading.
Vehicle direction is displayed as follows:
• N: north
• E: east
• S: south
• W: west
ZONE VARIATION SETTING PROCEDURE
The difference between magnetic north and geographical north can sometimes be great enough to cause
false compass readings. This difference is known as variance. In order for the compass to operate properly
(accurately) in a particular zone, the zone variation must be calibrated using the following procedure.
Zone Variation Chart
1. Determine your location on the zone map.
2. Turn the ignition switch to the ON position.
3. Hold the mode (N) switch down until the current zone number is displayed.
4. Press the mode (N) switch repeatedly until the desired zone number appears in the display.
Compass will exit zone setting mode and display correct heading automatically.
NOTE:
Use zone number 5 for Hawaii.
CALIBRATION PROCEDURE
The compass display is equipped with an automatic correction function. If the compass display reads “C” or
the direction is not shown correctly, perform the correction procedure below.
LKIA0447E
WKIA4148E
MWI-28
< SYSTEM DESCRIPTION >
COMPASS
1. Hold the mode (N) switch until the display reads “C”.
2. Drive the vehicle slowly in a circle, in an open, safe place. The
initial calibration is completed in about three turns.
NOTE:
In places where the terrestrial magnetism is extremely disturbed, the
initial correction may start automatically.
LKIA0447E
MWI
DIAGNOSIS SYSTEM (METER)
MWI-29
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (METER)
Diagnosis Description
INFOID:0000000010049564
SELF-DIAGNOSIS MODE
• Odo/trip meter and information display segment operation can be checked in self-diagnosis mode.
• Meters/gauges can be checked in self-diagnosis mode.
OPERATION PROCEDURE
1. Turn the ignition switch OFF.
2. While pushing the odo/trip meter switch, turn the ignition switch ON again.
3. Push the odo/trip meter switch at least 3 times within 7 seconds after the ignition switch is turned ON.
4. The unified meter control unit is turned to self-diagnosis mode.
• All the segments on the odo/trip meter illuminate.
• Dots in all segments of information display LCD (1) flash alter-
nately.
NOTE:
If any of the segments are not displayed, replace the combina-
tion meter. Refer to
MWI-122, "Removal and Installation"
.
5. Push the odo/trip meter switch. Each meter/gauge should indicate as shown in the figure.
CONSULT Function (METER/M&A)
INFOID:0000000010049565
CONSULT can display each diagnostic item using the diagnostic test modes shown following.
SKIB1206J
JSNIA0020GB
AWNIA2309ZZ
MWI-30
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (METER)
SELF-DIAG RESULTS
Display Item List
.
DATA MONITOR
Display Item List
X: Applicable
METER/M&A diagnosis mode
Description
SELF DIAGNOSTIC RESULT
Displays combination meter self-diagnosis results.
DATA MONITOR
Displays combination meter input/output data in real time.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
Display item [Unit]
MAIN
SIGNALS
SELECTION
FROM MENU
Description
SPEED METER [km/h] or [mph]
X
X
Displays the value of vehicle speed signal.
SPEED OUTPUT [km/h] or [mph]
X
X
Displays the value of vehicle speed signal, which is transmitted to
each unit with CAN communication.
ODO OUTPUT
X
Displays the value, which is calculated by vehicle speed signal.
TACHO METER [rpm]
X
X
Displays the value of engine speed signal, which is input from ECM.
FUEL METER [lit.]
X
X
Displays the value, which processes a resistance signal from fuel
gauge.
W TEMP METER [
°C] or [°F]
X
X
Displays the value of engine coolant temperature signal, which is in-
put from ECM.
ABS W/L [ON/OFF]
X
Displays [ON/OFF] condition of ABS warning lamp.
VDC/TCS IND [ON/OFF]
X
Displays [ON/OFF] condition of VDC/TCS OFF indicator lamp.
SLIP IND [ON/OFF]
X
Displays [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L [ON/OFF]
X
Displays [ON/OFF] condition of brake warning lamp.*
DOOR W/L [ON/OFF]
X
Displays [ON/OFF] condition of door warning lamp.
TRUNK/GLAS-H [ON/OFF]
X
Displays [ON/OFF] condition of trunk warning lamp.
HI-BEAM IND [ON/OFF]
X
Displays [ON/OFF] condition of high beam indicator.
TURN IND [ON/OFF]
X
Displays [ON/OFF] condition of turn indicator.
LIGHT IND [ON/OFF]
X
Displays [ON/OFF] condition of light indicator.
OIL W/L [ON/OFF]
X
Displays [ON/OFF] condition of oil pressure warning lamp.
MIL [ON/OFF]
X
Displays [ON/OFF] condition of malfunction indicator lamp.
CRUISE IND [ON/OFF]
X
Displays [ON/OFF] condition of CRUISE indicator.
CVT IND [ON/OFF]
X
Displays [ON/OFF] condition of CVT warning lamp.
FUEL W/L [ON/OFF]
X
Displays [ON/OFF] condition of low-fuel warning lamp.
WASHER W/L [ON/OFF]
X
Displays [ON/OFF] condition of low washer fluid warning lamp.
AIR PRES W/L [ON/OFF]
X
Displays [ON/OFF] condition of tire pressure warning lamp.
KEY G/Y W/L [ON/OFF]
X
Displays [ON/OFF] condition of key warning lamp.
LCD
X
Displays the value of Intelligent Key system message indication.
SHIFT IND [P, R, N, D]
X
Displays [P, R, N, D] range position of CVT.
FUEL CAP W/L [ON/OFF]
X
Status of fuel filler cap warning display detected from fuel filler cap
warning display signal received from ECM via CAN communication.
M RANGE SW [ON/OFF]
X
Displays [ON/OFF] condition of instruction mode range switch.
NM RANGE SW [ON/OFF]
X
Displays [ON/OFF] condition of except for instruction mode range
switch.
ST SFT UP SW [ON/OFF]
X
Displays [ON/OFF] condition of steering shift-up switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст