Nissan Maxima. Instruction — part 660
FAX-16
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT DRIVE SHAFT
8. Install boot securely into grooves (indicated by * marks) as
shown.
CAUTION:
• If there is grease on boot mounting surfaces (indicated by
* marks) of shaft and housing, boot may come off. Clean
all grease from surfaces.
• Do not reuse boot.
9. Make sure boot installation length (L) is the length specified
below. Insert a suitable tool into the large end of boot. Bleed air
from boot to prevent boot deformation.
CAUTION:
• Boot may break if boot installation length is less than standard value.
• Be careful that the tool does not contact inside surface of boot.
10. Secure large end of boot with new boot band as shown.
a. Put boot band in groove of drive shaft boot. Then insert pawls
into holes.
CAUTION:
Do not reuse boot bands.
NOTE:
Insert projection (A) and guide slit (B).
: Pawl
b. Pinch projection on boot band with suitable pliers to tighten
band.
c.
Insert tip of band below end of pawl.
: Pawl
11. Install new small boot band securely using Tool.
CAUTION:
• Do not reuse boot bands.
Boot installation length (L) : Refer to
.
JPDIF0144ZZ
JPDIF0157ZZ
JPDIF0158ZZ
Tool number
: KV40107300 (
—
)
RAC1133D
FRONT DRIVE SHAFT
FAX-17
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Secure boot band so that dimension (M) meets specifica-
tion as shown.
12. Install new dust shield to slide joint housing.
CAUTION:
Do not reuse dust shield.
13. After installing housing and shaft, make sure boot position is correct. If boot position is not correct, remove
old boot bands then reposition the boot and secure with new boot bands.
Wheel Side
1. Add grease (Genuine NISSAN Grease or equivalent) into joint
sub-assembly serration hole until grease begins to ooze from
ball groove and serration hole. After inserting grease, use a
shop cloth to wipe off old grease that has oozed out.
2. Cover serrated part of shaft with tape. Install new boot band and
boot to shaft. Be careful not to damage boot.
CAUTION:
Do not reuse boot band and boot.
3. Remove protective tape wound around serrated part of shaft.
4. Attach new circlip to shaft. The circlip must fit securely into shaft
groove. Attach nut to joint sub-assembly.
Use a suitable tool to press-fit.
CAUTION:
Do not reuse circlip.
5. Insert the amount of new grease (Genuine NISSAN Grease or equivalent) listed below into housing from
large end of boot.
Dimension (M)
: Refer to
.
AWDIA0598ZZ
SDIA1127E
SFA800
RAC0049D
Grease quantity
: Refer to
FAX-18
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT DRIVE SHAFT
6. Install boot securely into grooves (indicated by * marks) as
shown.
CAUTION:
• If there is grease on boot mounting surfaces (indicated by
* marks) of shaft and housing, boot may come off.
Remove all grease from surfaces.
• Do not reuse boot.
7. Make sure boot installation length (L) is the specified length indi-
cated below. Insert a suitable tool into the large end of boot.
Bleed air from boot to prevent boot deformation.
CAUTION:
• Boot may break if boot installation length is less than standard value.
• Be careful that the tool does not contact inside surface of boot.
8. Install new large and small boot bands securely using Tool.
CAUTION:
• Do not reuse boot bands.
• Secure boot band so that dimension (M) meets specifica-
tion as shown.
9. After installing housing and shaft, rotate boot to check whether or not the actual position is correct. If boot
position is not correct, remove old boot bands then reposition the boot and secure with new boot bands.
Damper
1. Use new damper bands for installation.
CAUTION:
Do not reuse damper bands.
2. Install damper from stationary-joint side while holding it securely.
Boot installation length (L)
: Refer to
Tool number
: KV40107300 (
—
)
JPDIF0142ZZ
RAC1133D
Dimension (M)
: Refer to
.
AWDIA0598ZZ
(A)
: Refer to
.
(B)
: Refer to
.
SFA313B
FRONT DRIVE SHAFT
FAX-19
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Disassembly and Assembly (RH)
INFOID:0000000009471152
DISASSEMBLY
Transaxle Side
1. Press shaft in a vise.
CAUTION:
When retaining shaft in a vise, always use copper or aluminum plates between vise and shaft.
2. Remove circlip and dust shield from slide joint housing.
3. Remove boot bands and slide the boot back.
4. Put matching marks on slide joint housing and shaft before separating slide joint housing.
5. Remove stopper ring using a suitable tool, then pull out slide
joint housing.
1.
Joint sub-assembly
2.
Circlip
3.
Boot band
4.
Boot
5.
Shaft
6.
Damper band
7.
Dynamic damper
8.
Stopper ring
9.
Spider assembly
10. Snap ring
11. Housing
12. Dust shield
13. Support bearing
14. Snap ring
15. Dust shield
16. Bearing housing
: Wheel side
: Fill using NISSAN Genuine grease or equivalent.
AWDIA0597ZZ
SFA476
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст