Nissan Maxima. Instruction — part 758
HAC-208
< REMOVAL AND INSTALLATION >
[WITH MONOCHROME DISPLAY]
REFRIGERANT PRESSURE SENSOR
REFRIGERANT PRESSURE SENSOR
Removal and Installation
INFOID:0000000009466452
REMOVAL
1. Discharge the refrigerant. Refer to
2. Remove the core support upper cover.
3. Disconnect the harness connector from the refrigerant pressure sensor.
4. Remove the refrigerant pressure sensor.
CAUTION:
Cap or wrap the opening of the refrigerant pressure sensor with suitable material such as vinyl
tape to avoid the entry of air.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply A/C oil to the O-ring of the refrigerant pressure sensor for installation.
• After charging refrigerant, check for leaks. Refer to
DOOR MOTOR
HAC-209
< REMOVAL AND INSTALLATION >
[WITH MONOCHROME DISPLAY]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
DOOR MOTOR
Exploded View
INFOID:0000000009466453
1.
Heating and cooling unit assembly
2.
Mode door motor
3.
Air mix door motor (driver side)
4.
Air mix door motor (passenger side) 5.
Intake door motor
ALIIA0644ZZ
HAC-210
< REMOVAL AND INSTALLATION >
[WITH MONOCHROME DISPLAY]
DOOR MOTOR
INTAKE DOOR MOTOR
INTAKE DOOR MOTOR : Removal and Installation
INFOID:0000000009466454
REMOVAL
1. Remove the glove box assembly. Refer to
IP-20, "Removal and Installation"
2. Remove the remote keyless entry receiver and bracket to reposition out of the way.
3. Disconnect the harness connector from the intake door motor.
4. Remove the intake door motor screws and the intake door motor from the blower unit.
INSTALLATION
Installation is in the reverse order of removal.
MODE DOOR MOTOR
MODE DOOR MOTOR : Removal and Installation
INFOID:0000000009466455
REMOVAL
1. Remove the combination meter. Refer to
MWI-122, "Removal and Installation"
2. Remove the BCM. Refer to
BCS-79, "Removal and Installation"
.
3. Disconnect the harness connector from the mode door motor.
4. Remove the mode door motor screws and the mode door motor.
INSTALLATION
Installation is in the reverse order of removal.
AIR MIX DOOR MOTOR
AIR MIX DOOR MOTOR : Removal and Installation - Air Mix Door Motor (Driver Side)
INFOID:0000000009466456
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-19, "Removal and Installation"
.
2. Remove the upper floor connecting duct (LH). Refer to
.
3. Remove the tire pressure receiver.
4. Disconnect the harness connector from the air mix door motor.
5. Remove the air mix door motor screws and the air mix door motor (driver side).
INSTALLATION
Installation is in the reverse order of removal.
AIR MIX DOOR MOTOR : Removal and Installation - Air Mix Door Motor (Passenger
Side)
INFOID:0000000009466457
REMOVAL
1. Remove the glove box assembly. Refer to
IP-20, "Removal and Installation"
2. Remove the upper floor connecting duct (RH). Refer to
3. Disconnect the harness connector from the air mix door motor.
4. Remove the air mix door motor screws and the air mix door motor (passenger side).
INSTALLATION
Installation is in the reverse order of removal.
HRN-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
HRN
A
B
HRN
N
O
P
CONTENTS
HORN
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ...
HORN . . . . . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
HORN . . . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст